NEC PD78214 User Manual
User's manual, Bit single-chip microcomputer
Advertising
USER'S MANUAL
µ
PD78214 SUB-SERIES
8-BIT SINGLE-CHIP MICROCOMPUTER
HARDWARE
µ
PD78212
µ
PD78213
µ
PD78214
µ
PD78P214
µ
PD78212 (A)
µ
PD78213 (A)
µ
PD78214 (A)
µ
PD78P214 (A)
Document No. IEU-1236H
(O. D. No. IEM-5119H)
Date Published September 1994 P
Printed in Japan
NEC Corporation 1989
Advertising
Table of contents
Document Outline
- COVER
- Main Revisions in This Edition
- PREFACE
- CHAPTER 1 GENERAL
- 1.1 FEATURES
- 1.2 ORDERING INFORMATION AND QUALITY GRADE
- 1.3 PIN CONFIGURATION (TOP VIEW)
- 1.4 EXAMPLE APPLICATION SYSTEM (PRINTER)
- 1.5 BLOCK DIAGRAM
- 1.6 FUNCTIONS
- 1.7 DIFFERENCES BETWEEN THE µPD78210Note AND µPD78213
- 1.8 DIFFERENCES BETWEEN THE µPD78214 SUB-SERIES AND µPD78218A SUB-SERIES
- 1.9 DIFFERENCES BETWEEN THE µPD78212 AND µPD78212(A)
- 1.10 DIFFERENCES BETWEEN THE µPD78213 AND µPD78214, AND THE µPD78213(A) AND µPD78214(A)
- 1.11 DIFFERENCES BETWEEN THE µPD78P214 AND µPD78P214(A)
- 1.12 DIFFERENCES BETWEEN THE µPD78212, µPD78213, µPD78214, AND µPD78P214
- CHAPTER 2 PIN FUNCTIONS
- CHAPTER 3 CPU FUNCTION
- CHAPTER 4 CLOCK GENERATOR
- CHAPTER 5 PORT FUNCTIONS
- CHAPTER 6 REAL-TIME OUTPUT FUNCTION
- CHAPTER 7 TIMER/COUNTER UNITS
- 7.1 16-BIT TIMER/COUNTER
- 7.2 8-BIT TIMER/COUNTER 1
- 7.3 8-BIT TIMER/COUNTER 2
- 7.3.1 Functions
- 7.3.2 Configuration
- 7.3.3 8-Bit Timer/Counter 2 Control Registers
- 7.3.4 Operation of 8-Bit Timer 2 (TM2)
- 7.3.5 External Event Counter Function
- 7.3.6 One-Shot Timer Function
- 7.3.7 Compare Register and Capture Register Operations
- 7.3.8 Basic Operation of Output Control Circuit
- 7.3.9 PWM Output
- 7.3.10 PPG Output
- 7.3.11 Sample Applications
- 7.4 8-BIT TIMER/COUNTER 3
- 7.5 NOTES
- CHAPTER 8 A/D CONVERTER
- CHAPTER 9 ASYNCHRONOUS SERIAL INTERFACE
- CHAPTER 10 CLOCK SYNCHRONOUS SERIAL INTERFACE
- 10.1 FUNCTION
- 10.2 CONFIGURATION
- 10.3 CONTROL REGISTERS
- 10.4 OPERATIONS IN THE THREE-WIRE SERIAL I/O MODE
- 10.5 SBI MODE
- 10.6 SBI COMMUNICATION AND SIGNALS
- 10.6.1 Bus Release Signal (REL)
- 10.6.2 Command Signal (CMD)
- 10.6.3 Address
- 10.6.4 Command and Data
- 10.6.5 Acknowledge Signal (ACK#)
- 10.6.6 Busy Signal (BUSY#) and Ready Signal (READY)
- 10.6.7 Signals
- 10.6.8 Communication
- 10.6.9 Releasing the Busy State
- 10.6.10 Setting Wake-Up
- 10.6.11 Starting Transmission and Reception
- 10.7 NOTES
- CHAPTER 11 EDGE DETECTION FUNCTION
- CHAPTER 12 INTERRUPT FUNCTIONS
- CHAPTER 13 LOCAL BUS INTERFACE FUNCTION
- CHAPTER 14 STANDBY FUNCTION
- CHAPTER 15 RESET FUNCTION
- CHAPTER 16 APPLICATION EXAMPLES
- CHAPTER 17 PROGRAMMING FOR THE µPD78P214
- CHAPTER 18 INSTRUCTION OPERATIONS
- APPENDIX A 78K/II SERIES PRODUCT LIST
- APPENDIX B DEVELOPMENT TOOLS
- APPENDIX C SOFTWARE FOR EMBEDDED APPLICATIONS
- APPENDIX D REGISTER INDEX
- APPENDIX E INDEX