NETGEAR FA511 User Manual

Install the windows xp network driver

Advertising
background image

This section explains how to install the Network Driver in various Microsoft Windows Operating Systems.
Some versions of Microsoft Windows Operating System may respond with different dialog boxes, or the
dialog boxes may open in a different sequence than those shown in this guide, but should prompt you for the
same information.

Note: You must install the network card before installing the network driver. If you have chosen to
install the card with the PC turned off, turn the power ON now.

Before you proceed with the installation steps, decide on a name for your network and for each PC. The
whole network must have the same workgroup name while each PC must have a unique name. These names
can be entered by going to Start>Settings>Control Panel>Network and clicking on the Identification tab.
You also need to have the Microsoft Windows Operating System CD-ROM and the GearBox™ for Adapters
CD ready to use in the installation process.

Please refer to README file in GearBox™ for Adapters CD and NETGEAR support website
for latest FAQ and trouble-shooting information.

Install the Windows XP Network Driver

Note: If the “Insert Disk” window opens and a message prompts you to insert your Windows
CD-ROM at any time during the installation process, insert the Windows CD-ROM in Drive D (the
CD-ROM drive) and click on “OK”. Then follow the next step in the instructions.

1. After installing the FA511 CardBus Notebook Adapter, Window XP will automatically install the build-

in driver. The following steps are for updated driver in GearBox™ for Adapters CD.

2. Double-click “My Computer” on the desktop, double-click “Control panel” and then double-click

“System”.

3. Click “Hardware” and click “Device Manager” tab, then double-click “Network adapters”.

4. Double-click “ADMtek AN985 10/100Mbps Fast Ethernet Adapter”.

5. Click “Driver” and click “Update Driver” tab, then click “OK”.

10/100 Mbps Fast Ethernet

FA511

CardBus Notebook Adapter

Installation Guide

Introduction

NETGEAR’s Model FA511 CardBus Notebook Adapter makes it easy to accelerate your notebook PC
to Fast Ethernet speeds. It is 32-bit CardBus compatible and, with its auto-sensing technology and
Ethernet/Fast Ethernet compatibility, ideal for migrating a 32-bit PC card notebook computer from
10 Mbps to 100 Mbps networks.

START HERE

Instructions in this guide are for users of Microsoft Windows Operating Systems.

As a last step, be sure to register your network card at

http://www.NETGEAR.com.

Plan Your Time

Estimated setup time for this product is only minutes.

Make sure that your package contains the following:

Preparation

You will need to have your Microsoft Windows Operating System CD-ROM (or Microsoft Windows
Operating System floppy disks) available to complete the installation.

Install the Network Card

The FA511 CardBus Notebook Adapter is hot swappable, which means you can insert it into a PC that
is either powered on or shut down.

1. Insert the FA511 CardBus Notebook Adapter into the CardBus slot as illustrated below.

Some PCs have two PCMCIA or CardBus slots; the FA511 CardBus Notebook Adapter can only be
inserted into cardBus slot.

2. Insert the RJ-45 adapter cable into the connector on the outer edge of the network card.

Connect the Network Cables

Using a UTP cable, connect any port on a hub or switch to the port on the network card.

Note: One of the ports on NETGEAR hubs is switchable between Normal (MDI-X) and Uplink
(MDI) with a Normal/Uplink push button. If you are using this switchable port on a NETGEAR
hub to connect to a PC or the network card, make sure the Normal/Uplink push button is set to
Normal.

Model FA511 Fast Ethernet
CardBus Notebook Adapter

Installation Guide,

and Support Information Card

GearBox

for Adapters CD

NETGEAR, Inc.

Support Information
Phone: 1-888-NETGEAR
E-mail: [email protected]
www.NETGEAR.com

See Support Information Card for for additional phone numbers.

Internet / World Wide Web

Go to http://www.NETGEAR.com for the NETGEAR Web page.
Defective or damaged merchandise can be returned to your point-of-sale representative.

IMPORTANT!

Please register online. YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE
RETAIN PROOF OF PURCHASE and this warranty information. To register your product, get product
support, or to obtain product information and NETGEAR product documentation, direct your Web
browser to the http://www.NETGEAR.com Web page.

July 2002

START HERE

1 OPEN BOX AND VERIFY CONTENTS

2 CONNECT NETGEAR TO YOUR ENVIRONMENT

Model FA511

CardBus Notebook Adapter

RJ-45

connectors

PC with network
card installed

Power adapter

Notebook PC

*Use any Category 5 UTP cable.
Maximum length = 100 meters (300 feet)

Category 5 10/100 Mbps UTP cables*

Model FA511
CardBus Notebook Adapter

Hub

M

1

-

F

A

5

1

1

N

A

-

2

6. A Hardware Update Wizard will appear. Insert the GearBox™ for Adapters CD into your CD-ROM

drive. Select “Install from a list or specific location ( Advanced )”. Click “Next”.

7. When the following dialog box opens, select “Don’t search. I will choose the driver to install.” then

click “Next”.

8. When Select Network Adapter box opens, click “Have Disk” then click “Next”.

9. The Install From Disk box will open. Type “D:\” and click “OK”.

10. “NETGEAR FA511 CardBus Mobile Adapter” will appear in the model list. Click “Next”.

11. The next Windows appears with the following adapter name : NETGEAR FA511 CardBus Mobile

Adapter. Click “Finish”.

12. Remove the GearBox™ for Adapters CD from the CD-ROM drive.

The Model FA511 CardBus Adapter driver installation for Windows XP is now complete.

1. Open the box

and verify its
contents

2. Connect NETGEAR to

your environment

3. Install Network Driver

4. Test Your Network Connection

5. Enjoy being connected!

3 INSTALL THE NETWORK DRIVER

Advertising