Ruby Tech PSES-2126C User Manual
Page 2
---IEEE802.1q tag-base VLAN, 4094
max, up to 256 active VLANs included
static plus dynamic entry
---IEEE802.1q tag-base VLAN
---Flooding unknown vlan frame setting,
can flood packet with some vlan tag
associated to a invalid/inactive vlan
---In tag-base VLAN, supports egress/
ingress packet filter
---Q-in-Q is an efficient method for
enabling Subscriber Aggregation.
QoS
---Port Based (VIP Port), 802.1p , TOS
and Diffserv(IPv4/IPv6) based QoS
packet classification
---Supports four level priority queues to
prioritize in-bound and out-bound
traffic
---Supports two scheduling, WRR and
Strict
---Supports priority in a Q-in-Q tag
Broadcast Storm
---Multicast/Broadcast/Unknown-Unicast
Storm suppression.
Port Mirroring
---Support 1: N RX port mirroring.
---Supports port sniffer function with 3
modes:
(TX Monitor Mode, RX Monitor Mode
and TX-RX pair Monitor Mode).
Isolated Group
---Provide one group allows certain
ports to be designated as protected.
Restricted Group
---Can decide the direction of
transmitting packets for the specific
port
Restricted Group
---Can decide the direction of tran
smitting packets for the specific port
Rate Limit
---Ingress rate limit:
Port 1~24: 1K up to 100Mbps
Port 25, 26: 1K up to 1000Mbps
---Egress rate limit:
Port 1~24: 1K up to 100Mbps
Port 25, 26: 1K up to 1000Mbps
PoE Specification
---24 IEEE802.3af PoE PSE ports
---Endpoint with 48VDC power through
RJ-45 pin 1, 2, 3, 6.
---PoE-PSE activity LED indicator.
---185 watts of total power (up to 15.4
watts for 12 ports, or up to 7.7 watts
for 24 ports)
---Auto detect powered device and
consumption levels
---Supports per port power consumption
monitoring
---Smart feature for PD on/off, PD
detection, power level, PD status and
power feeding priority
---Circuit protection to prevent power
interference between ports
---Supports per port PoE State setting
transmission and reception of packets can be guaranteed in event of any fail-
over switch on the network.
2 Dual Media for Flexible Fiber Connection
Dual media port 25 and 26 are provided for flexible fiber connection. You can
select to install optional transceiver modules in these slots for short, medium
or long distance fiber backbone attachment. Use of the SFP will disable their
corresponding built-in 10/100/1000Base-T connections.
Broadcast/Multicast/Unknown-unicast Storm Control
To limit too many broadcast/multicast/unknown-unicast flooding in the network,
broadcast/multicast storm control is used to restrict excess traffic. Threshold
values are available to control the rate limit for each port. Packets are
discarded if the count exceeds the configured upper threshold.
Technical Specifications
Technical Specifications
LED Description
Cable and Maximum Length
:
LED Color Function
System LED
CPURUN Green -Blinks when CPU is on and good
POWER Green -Lit when AC power is on and good
ACT Green -Lit when LEDSET set on active mode
FDX Green -Lit when LEDSET set on full-duplex mode
SPD Green -Lit when LEDSET set on speed mode
10/100Mbps Ethernet TP Port 1 to 24 LED
LNK Green -Lit when connection with remote device is good
-Off when cable connection is not good
ACT/FDX Amber (a)LEDSET set on ACT (active) mode:
/ SPD (TP Port -Blinks when any traffic is present
1 to 24 (b)LEDSET set on FDX (full-duplex) mode:
LED) -Lit when full-duplex mode is active
-Blinks when any collision is present
(c)LEDSET set on SPD (speed) mode:
-Lit when 100Mbps speed is active
-Off when 10Mbps speed is active
10/100/1000Mbps Gigabit TP/Fiber Port 25, 26 LED
LNK Green -Lit when connection with remote device is good
-Off when cable connection is not good
FX Green -Lit when Fiber port is active
-Off when TP port is active
ACT/FDX Green (a)LEDSET set on ACT (active) mode:
/ SPD (Port 25, -Blinks when any traffic is present
26 LED) (b)LEDSET set on FDX (full-duplex) mode:
-Lit when full-duplex mode is active
-Blinks when any collision is present
(c)LEDSET set on SPD (speed) mode:
-Lit when 1000Mbps speed is active
-Off when 10/100Mbps speed is active
PoE Port Status Indication LEDs
PoE-PSE Green -Lit when PoE Power is active
ACT
G
i
g
a
b
i
t
S
w
i
t
c
h
Gigabit Switch
L2 Managed PoE Switch
TP Cat. 5 UTP cable, up to 100m
1000Base-SX SC M-M Up to 220/275/500/550m,
which depends on Multi-Mode Fiber type
1000Base-LX SC S-M Single-Mode Fiber, up to10/30/50Km
1000Base-LX WDM SC S-M Single-Mode Single Fiber, Bidi 20Km
RUB
TECH
Networking & Communications
R