Document Outline

• RuncoCare™ Standard Two Year Limited Warranty
• Important Safety Instructions
• Compliance Information
• 1. Introduction
  • 1.1 About This Manual
    • Target Audience
    • If You Have Comments About This Manual...
    • Textual and Graphic Conventions
      • Text Conventions
      • Graphic Conventions
  • 1.2 Using This Manual
  • 1.3 Description, Features and Benefits
    • Key Features and Benefits
    • Parts List
      • Optional Accessories
• 2. Controls and Functions
  • 2.1 LS-7 at a Glance
    • Figure 2-1 . LS-7 Front/Side View
    • Figure 2-2 . LS-7 Rear/Bottom/Top View
  • 2.2 LS-7 Rear Panel
    • Figure 2-3 . LS-7 Rear Panel
  • 2.3 LS-7 Remote Control
• 3. Installation
  • 3.1 Remote Control
    • Notes on Batteries
    • Notes on Remote Control Operation
      • Figure 3-1 . IR Reception Angles
  • 3.2 Quick Setup
    • Table 3-1 . Installation Overview
  • 3.3 Installation Considerations
    • Installation Type
      • Table 3-2 . Projector Installation Options
    • Ambient Light
    • Throw Distance
      • Figure 3-2 . Estimating Throw Distance
      • Table 3-3 . Throw Ratios for the LS-7 Series
    • Vertical and Horizontal Position
      • Figure 3-3 . Projector Placement
    • Lens Shift
      • Figure 3-4 . Vertical Lens Shift (Example Only)
      • Figure 3-5 . Horizontal Lens Shift (Example Only)
      • Vertical Lens Shift
      • Horizontal Lens Shift
    • Folded Optics
      • Figure 3-6 . Folded Optics
    • Other Considerations
  • 3.4 Mounting the LS-7
    • Floor Mounting (Upright)
    • Ceiling Mounting (Inverted)
    • Adjusting the Projection Angle
  • 3.5 Connections to the LS-7
    • Connector Panel Access
    • Connecting Source Components to the LS-7
      • HDMI/DVI Connections
        • Figure 3-7 . HDMI/DVI Source Connections
      • RGB Connections
        • Figure 3-8 . RGB Connections
      • Component Video Connections
        • Figure 3-9 . Component Video Connections
      • Composite/S-Video Connections
        • Figure 3-10 . Composite and S-Video Connections
    • RS-232 Controller Connection
      • Figure 3-11 . RS-232 Control System Connection
    • Connecting 12-Volt Trigger Output to External Theater Equipment
      • Figure 3-12 . 12-Volt Trigger Output Connection
    • Connecting an External IR Receiver
      • Figure 3-13 . External IR Receiver Connection
    • Connecting to AC Power
  • 3.6 Turning on the Power
  • 3.7 Lens Adjustments
    • Focus
    • Zoom
    • Lens Shift
      • Installing the Optional Stray Light Shield
  • 3.8 Changing the OSD Language
  • 3.9 Adjusting the Picture Orientation
    • Rear Projection
    • Ceiling Mode
• 4. Operation
  • 4.1 Selecting Video Memory
  • 4.2 Selecting an Aspect Ratio
  • 4.3 Selecting An Input Source
  • 4.4 Using Picture-In-Picture (PIP)
    • Table 4-1 . Available Main and PIP Source Combinations
  • 4.5 Using the On-Screen Menus
    • Figure 4-1 . LS-7 OSD Menu Structure
    • Main
      • Figure 4-2 . LS-7 Main Menu
      • Aspect Ratio
        • Table 4-2 . Aspect Ratio Settings
      • Memory
      • Brightness
        • Figure 4-3 . Typical PLUGE Pattern for Adjusting Brightness
      • Contrast
        • Figure 4-4 . Typical Gray Bar Pattern for Adjusting Contrast
      • Color
      • Color Tint
      • Sharpness
        • Figure 4-5 . Typical Test Pattern for Adjusting Sharpness
      • Noise Reduction
      • Overscan
        • Figure 4-6 . Overscan Examples
      • Source Select
        • Figure 4-7 . Source Select Sub-Menu
      • PIP Select
      • Resync
    • Advanced
      • Figure 4-8 . LS-7 Advanced Menu
      • Color Space
      • Video Standard
      • Gamma
      • Color Temperature
      • DLP Frame Rate
      • Color Gamut
        • Table 4-3 . x/y Color Gamut Values
      • ConstantContrast
      • Adaptive Contrast
      • RGB Adjust
        • Figure 4-9 . RGB Adjust Sub-Menu
      • Fine Sync
        • Figure 4-10 . Fine Sync Sub-Menu
    • System
      • Figure 4-11 . LS-7 System Menu
      • Source Enable
        • Figure 4-12 . Source Enable Sub-Menu
      • PIP Position
        • Figure 4-13 . PIP and PBP areas for 720p Display
        • Figure 4-14 . PIP Split-Screen Mode
      • Menu Position
      • Translucent Menu
      • Lamp Power
      • Blank Screen
      • Auto Power Off
      • Auto Power On
      • Rear Projection
      • Ceiling Mode
      • Power On Chime
    • Control
      • Figure 4-15 . LS-7 Control Menu
      • Lens Control
      • 1 Key / 2 Key / 3 Key / 4 Key / 5 Key
      • M1 Key / M2 Key / M3 Key
      • Trigger 1
      • Trigger 2
      • Remote Code Set
      • Auto Source
    • Language
    • Service
      • Figure 4-16 . LS-7 Service Menu
      • Lamp Hour Reset
      • Factory Reset
      • Blue Only
      • Test Patterns
      • Altitude
• 5. Maintenance and Troubleshooting
  • 5.1 Lamp Replacement
  • 5.2 Troubleshooting Tips
    • Table 5-1 . Troubleshooting Chart
• 6. Serial Communications
  • 6.1 RS-232 Connection and Port Configuration
  • 6.2 Serial Command Syntax
    • Key Commands
      • Table 6-1 . Serial Command Key Names and IR Codes
    • Operations Commands
      • Table 6-2 . Serial Commands
    • RS-232 Error Codes
      • Table 6-3 . RS-232 Error Codes
• 7. Specifications
  • 7.1 LS-7 Specifications
    • Table 7-1 . LS-7 Specifications
  • 7.2 LS-7 Dimensions
    • Figure 7-1 . LS-7 Dimensions
  • 7.3 Supported Timings
    • Table 7-2 . Supported Signal Timings by Input