Roland Fantom-X7 - Manual (Page 271)

271
Effects List
01: EQUALIZER
This is a four-band stereo equalizer (low, mid x 2, high).
fig.MFX-01
02: SPECTRUM
This is a stereo spectrum. Spectrum is a type of filter which modifies
the timbre by boosting or cutting the level at specific frequencies.
fig.MFX-02
03: ISOLATOR
This is an equalizer which cuts the volume greatly, allowing you to
add a special effect to the sound by cutting the volume in varying
ranges.
fig.MFX-03
04: LOW BOOST
Boosts the volume of the lower range, creating powerful lows.
fig.MFX-04
Parameter Value Description
Low Freq 200, 400 Hz Frequency of the low range
Low Gain # -15– +15 dB Gain of the low range
Mid1 Freq 200–8000 Hz Frequency of the middle
range 1
Mid1 Gain -15– +15 dB Gain of the middle range 1
Mid1 Q 0.5, 1.0, 2.0, 4.0, 8.0 Width of the middle range 1
Set a higher value for Q to
narrow the range to be af-
fected.
Mid2 Freq 200–8000 Hz Frequency of the middle
range 2
Mid2 Gain -15– +15 dB Gain of the middle range 2
Mid2 Q 0.5, 1.0, 2.0, 4.0, 8.0 Width of the middle range 2
Set a higher value for Q to
narrow the range to be af-
fected.
High Freq 2000, 4000, 8000 Hz Frequency of the high range
High Gain # -15– +15 dB Gain of the high range
Level # 0–127 Output Level
Parameter Value Description
Band1 (250Hz) -15– +15 dB Gain of each frequency band
Band2 (500Hz)
Band3 (1000Hz)
Band4 (1250Hz)
Band5 (2000Hz)
Band6 (3150Hz)
Band7 (4000Hz)
Band8 (8000Hz)
Q
0.5, 1.0, 2.0, 4.0, 8.0 Simultaneously adjusts the
width of the adjusted ranges for
all the frequency bands.
Level # 0–127 Output Level
L in
R in
L out
R out
4-Band EQ
4-Band EQ
L in
R in
L out
R out
Spectrum
Spectrum
Parameter Value Description
Boost/
Cut Low # -60– +4 dB These boost and cut each of the High,
Middle, and Low frequency ranges.
At -60 dB, the sound becomes in-
audible. 0 dB is equivalent to the
input level of the sound. Boost/
Cut Mid #
Boost/
Cut High #
Anti Phase
Low Sw
OFF, ON Turns the Anti-Phase function on and
off for the Low frequency ranges.
When turned on, the counter-
channel of stereo sound is inverted
and added to the signal.
Anti Phase
Low Level 0–127 Adjusts the level settings for the Low
frequency ranges.
Adjusting this level for certain fre-
quencies allows you to lend em-
phasis to specific parts. (This is
effective only for stereo source.)
Anti Phase
Mid Sw OFF, ON Settings of the Anti-Phase function
for the Middle frequency ranges
The parameters are the same as for
the Low frequency ranges. Anti Phase
Mid Level 0–127
Low Boost Sw OFF, ON Turns Low Booster on/off.
This emphasizes the bottom to cre-
ate a heavy bass sound.
Low Boost
Level 0–127 Increasing this value gives you a
heavier low end.
* Depending on the Isolator and fil-
ter settings this effect may be hard
to distinguish.
Level 0–127 Output Level
Parameter Value Description
Boost
Frequency # 50–125 Hz Center frequency at which the lower
range will be boosted
Boost Gain # 0– +12 dB Amount by which the lower range
will be boosted
Boost Width WIDE, MID,
NARROW Width of the lower range that will be
boosted
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
L in
R in
L out
R out
Isolator
Low Boost
Low Boost
Isolator
L in
R in
L out
R out
Low Boost
2-Band EQ
2-Band EQ
Low Boost
Fantom-X678_r_e.book 271 ページ ２００５年５月１２日 木曜日 午後４時４０分