Onkyo TX-NR3008 - Manual (Page 48)

48
En
■
Resolution
You can specify the output resolution for the HDMI output
and COMPONENT VIDEO MONITOR OUT and have
the AV receiver upconvert the picture resolution as neces-
sary to match the resolution supported by your TV.
` Through *1 :
Select this to pass video through the AV receiver at
the same resolution and with no conversion.
` Auto *2 :
Select this to have the AV receiver automatically
convert video at resolutions not supported by your
TV.
` 480p (480p/576p):
Select this for 480p or 576p output and video con-
version as necessary.
` 720p:
Select this for 720p output and video conversion as
necessary.
` 1080i:
Select this for 1080i output and video conversion as
necessary.
` 1080p *2 :
Select this for 1080p output and video conversion as
necessary.
` 1080p/24 *2 :
Select this for 1080p output at 24 frames per second
and video conversion as necessary.
`
Source:
Output will be according to the resolution level
which was set in the “Picture Adjust” setting
(
➔ 60).
Tip
• The “Resolution” setting is set respectively of main, sub, and
analog.
Note
• If the “Monitor Out” setting is set to “Both”, this setting is fixed
at “Auto”.
• Depending on the incoming video signal, video playback may
not be smooth or the vertical resolution may be lowered. In this
case select other than “1080p/24”.
*1 PC IN (Analog RGB) input signal is output at 480p (480p/
576p), 720p, 1080i resolution when the “Monitor Out” set-
ting is set to “Analog” (
➔ 47) and the “Resolution” setting is
set to “Through”.
*2 These settings are not available when the “Monitor Out” set-
ting is set to “Analog” (
➔ 47).
HDMI Input
If you connect a video component to an HDMI input, you
must assign that input to an input selector. For example, if
you connect your Blu-ray Disc/DVD player to HDMI
IN 2, you must assign “HDMI 2” to the “BD/DVD” input
selector.
If you’ve connected your TV to the AV receiver with an
HDMI cable, composite video, S-video and component
video sources can be upconverted
* and output by the
HDMI output *1 . You can set this for each input selector by
selecting the “- - - - -” option.
*1 This applies only when “Monitor Out” setting is set to other
than “Analog” (
➔ 47).
Here are the default assignments.
■ BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, TAPE,
TV/CD, PHONO, PORT
` HDMI 1, HDMI 2, HDMI 3, HDMI 4, HDMI 5,
HDMI 6, HDMI 7:
Select the HDMI IN to which the video component
has been connected.
` - - - - -:
Output composite video, S-Video, and component
video sources from the HDMI output. The video out-
put signal from the HDMI output is the one config-
ured in “Component Video Input” (
➔
49).
• “AUX” is used only for input from the front panel.
• Each HDMI input cannot be assigned to two input selec-
tors or more. When HDMI 1 - HDMI 7 have already
been assigned, you must set first any unused input selec-
tors to “- - - - -” or you will be unable to assign HDMI 1
- HDMI 7 to input selector.
Input selector Default assignment
BD/DVD HDMI 1
VCR/DVR HDMI 2
CBL/SAT HDMI 3
GAME HDMI 4
PC HDMI 5
AUX FRONT (Fixed)
TAPE - - - - -
TUNER - - - - - (Fixed)
TV/CD - - - - -
PHONO - - - - -
PORT - - - - -
IN
OUT
Composite video, S-Video,
component video
Composite video, S-Video,
component video
HDMI
HDMI