Traulsen RBC100 EN - Manual (Page 11)

10
Resetting The Control
Refers To Older Control Versions Only
If memory reaches capacity during a chill cycle there is potential that some printout data could
be incorrect (date & time). This will reset on it’s own, however to do so manually...
FACTORY SETTINGS
VERSION 2.0
S/N:T00000A00
RESET NEXT
STEP 6
Serial number will be
displayed. Press NEXT.
STEP 5
FACTORY SETTINGS
menu. Press RESET.
STEP 10
Press NEXT.
↓ ↓ ↓ ↓ ↓ DEFROST TIME (40) ↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ DEFR. TEMP (50) ° F ↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ DEFR. INTVL (3) HR ↑ ↑ ↑ ↑ ↑
BACK NEXT
STEP 9
Press NEXT.
STEP 13
Press YES.
STEP 11
Press ENTER.
(do not change code)
S E L E C T S U P E R V I S O R :
↓ ↓ ↓ ↓ ↓ PRESET SUPERVISOR ↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ PASSWORD (PIN): 00 ↑ ↑ ↑ ↑ ↑
CANCEL ENTER
↓ ↓ ↓ ↓ ↓ BLASTING DIFF (4) ° F ↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ HOLDING DIFF (3) ° F ↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ ANTI-SHORT(1) ↑ ↑ ↑ ↑ ↑
BACK NEXT
ENTER SECURITY CODE
FOR NEXT SETTINGS:
↓ ↓ ↓ ↓ ↓ (000000) ↑ ↑ ↑ ↑ ↑
EXIT ENTER
FACTORY SETTINGS
DO YOU WISH TO SAVE
THESE NEW SETTINGS
NO YES
STEP 1
Main Menu display press MORE
STEP 2
Press SETUP.
STEP 3
Enter PASSWORD/PIN 85.
S E L E C T S U P E R V I S O R :
↓ ↓ ↓ ↓ ↓ TIM SMITH ↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ PASSWORD (PIN): 85 ↑ ↑ ↑ ↑ ↑
CANCEL ENTER
DISPLAY WILL SHOW
SELECT SUPERVISOR screen
MAIN MENU AIR 35 ° F
BY TEMP BY PROD
BY TIME
08:05:01 MORE
MAIN MENU 08:06:01
HOLD PROD PRINT
DEFROST
SETUP
BACK
STEP 4
Press the top left, top
right, and bottom right buttons
at the same time.
FACTORY SETTINGS
VERSION 2.0
S/N:T00000A00
RESET NEXT
↓ ↓ ↓ ↓ ↓ LABEL PRINTER (NO) ↑ ↑ ↑ ↑ ↑
RESET NEXT
↓ ↓ ↓ ↓ ↓ LABEL PRINTER(YES) ↑ ↑ ↑ ↑ ↑
RESET NEXT
STEP 7
Display will ask LABEL
PRINTER (NO), press the UP
arrow to select YES.
STEP 8
Press NEXT.
NEW SOFTWARE
HAS BEEN INSTALLED
SYSTEM PARAMETERS
HAVE BEEN SET!
DISPLAY WILL SHOW
↓ ↓ ↓ ↓ ↓ MACH. MODEL (RBC) ↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ MACHINE SIZE(50) ↑ ↑ ↑ ↑ ↑
RESET EXIT
STEP 12
↓ ↓ ↓ ↓ ↓ MACH. MODEL (RBC) ↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ MACHINE SIZE(50) ↑ ↑ ↑ ↑ ↑
RESET EXIT
14. The display will return to the MAIN
MENU. Repeat steps 1-10
15. Press EXIT.
16. Press YES.
Display will ask MACHINE SIZE. Press RESET,
then using the UP or DOWN arrow change for
your model. For RBC50 = 50, RBC100 = 100,
RBC200 = 200. Press EXIT.