Vision Fitness COMMERCIAL FITNESS BIKES R70 - Manual (Page 3)

2 STEP
• Slide the console mast boot onto the
console mast.
• Unfold the wire harness and heart
rate wires located in the console
mast frame bracket. Attach the wire
tie coming from the bottom of the
console mast to the wire harness and
heart rate wires. Pull the wire tie with
wire harness and heart rate wires up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket.
• Secure the console mast to the
frame bracket with six bolts (M8x15L).
Tighten with the 5mm T-Shaped
wrench. Insert a set screw (M10x12L)
to the front edge of the mast and
tighten until snug with the 5mm T-shaped
wrench.
• Slide the console mast boot down
and snap it into place on the side
cover.
BLUE BAG
3 STEP
• Mount the upper handlebars to the
console mast using two lock washers
(M8) and two bolts (M8x15L). Tighten
with the 5mm T-Shaped wrench.
• Remove the four mounting screws
from the back of the console. Remove
the four console back cover screws.
Connect the wire harness and heart rate
wires that come from the console mast
into the plugs located in the back of the
console. Attach the console to the mast
with the four screws removed earlier.
• Plug in the 9-volt battery. Re-attach
the console back cover with the four
screws previously removed.
PINK BAG
1 STEP
• Install the rear foot with the four
lock washers (M8), two inside bolts
(M8x65L), and two outside bolts
(M8x20L). Tighten with the 5mm
T-Shaped wrench.
ORANGE BAG
A s s e m b l y
G u i d e
R70
COMMERCIAL FITNESS BIKES
1 STEP
4 STEP
• Remove the two socket head bolts
from the sliding seat adjustment brack-
et. Slide the seat adjustment handle
between the teeth of the seat adjust-
ment bracket. Re-insert the two socket
head bolts and tighten with the 4mm
L-shaped wrench.
• Attach the seat frame to the sliding
seat bracket using four lock washers
(M8) and four bolts (M8x20L) and the
5mm T-Shaped wrench.
• Connect Wires A on the seat
handlebar to Wires B on the sliding
seat bracket. Connect the wire har-
ness coming from the seat frame to the
wire harness in the handlebars. Attach
the seat handlebars to the sliding seat
bracket using four lock washers (M8)
and four bolts (M8x20L). Tighten with
the 5mm T-Shaped wrench.
GREEN BAG
2
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.
Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble
your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws
and bolts are in place and partially threaded in before completely tightening any ONE screw or bolt.
5 STEP
4
STEP
5
STEP
• Mount the seat bottom and seat
back to the seat frame with four
bolts (M6x55L) and four lock washers
(M6). Tighten with the 4mm L-shaped
wrench.
BLACK BAG
3 STEP
Wires B
Wires A
6
STEP
• Attach the left and right pedals to
the left and right crank arms. Tighten
the pedals using the 15mm Pedal
Wrench.
• Secure the Accessory Tray to
the seat handlebar with two bolts
(M5x35L) and two lock washers
(M5). Be careful when inserting the
bolts to clear the wires inside the
handlebar to prevent damage. Tighten
with the screwdriver.
YELLOW BAG
6
STEP
Seat Bottom
Console Mast
Handlebar
Seat Handlebar
Seat Frame
Console Mast
Console Mast
Boot
Frame
Bracket
Rear Foot
Accessory
Tray Pedal
Sliding Seat
Bracket
Console Back Cover
Console
R70 AG_091217.indd 2 12/17/09 1:56 PM