Vista 20SE User Manual
Page 6
– 6 –
TO PROGRAM SYSTEM STATUS, & RESTORE
REPORT CODES (
*
59Ð
*
76, &
*
89):
With a 3+1 or 4+1 Standard Format:
Enter a code in the
first
box: 1–9, 0, B, C, D, E, or F. Enter "#+10" for 0, "#+11" for B,
"#+12" for C, "#+13" for D, "#+14" for E, "#+15" for F.
A "0" (
not "#+10") in the first box will disable a report.
A "0" (
not "#+10") in the second box will result in auto matic
advance to the next field when programming.
With an Expanded or 4+2 Format:
Enter codes in
both boxes
(1st and 2nd digits) for 1–9, 0, or B–F, as de scribed above.
A "0" (
not "#+10") in the second box will eliminate the ex-
panded message for that report.
A "0" (
not "#+10") in both boxes will disable the report.
With Ademco Contact ID Reporting:
Enter any digit (other
than "0") in the
first box, to enable zone to report (entries in the
second boxes will be ignored).
A "0" (
not "#+10") in the first box will disable the report.
Examples:
For Code
3
(single digit), enter: 3 | 0
For Code
3 2
(two digits), enter: 3 | 2
For Code
B 2
(Hexadecimal), enter: #+11 | 2
SYSTEM STATUS REPORT CODES (
*
59–
*
68)
Default for all report codes = [00]
*
59
EXIT ERROR REPORT CODE
*
60
TROUBLE REPORT CODE
|
*
61
BYPASS REPORT CODE
|
*
62
AC LOSS REPORT CODE
t
|
*
63
LOW BAT REPORT CODE
t
|
*
64
TEST REPORT CODE
|
*
65
OPEN REPORT CODE
Part. 1
††
Part. 2
††
*
66
ARM AWAY/STAY RPT CODE
Part. 1
††
AWAY STAY
Part. 2
††
AWAY STAY
† 2nd digit is automatically sent as the 2nd digit of the
zone alarm report code programmed in
*
56, if
expanded or 4+2 report ing is selected.
†† 2nd digit is automatically sent as the user number if
expanded or 4+2 reporting is selected.
*
67
RF XMTR LOW BAT REPORT CODE
|
*
68
CANCEL REPORT CODE
|
RESTORE REPORT CODES (
*
70–
*
76)
Default for all restore report codes = [00]
*
70
ALARM RESTORE RPT CODE
2nd digit is automatically sent as the 2nd digit of
the zone alarm report code programmed in
*
56, if
expanded or 4+2 re porting is selected.
*
71
TROUBLE RESTORE RPT CODE
|
*
72
BYPASS RESTORE RPT CODE
|
*
73
AC RESTORE RPT CODE
t
|
*
74
LOW BAT RESTORE RPT CODE
t
|
t
Reports with Partition 1 Subscriber No.
*
75
RF XMTR LO BAT RST RPT CODE
|
*
76
TEST RESTORE RPT CODE
|
OUTPUT AND SYSTEM SETUP (
*
80–
*
93)
*
80
OUTPUT RELAYS AND
POWERLINE CARRIER
DEVICES
*
81
ZONE LISTS FOR OUTPUT
DEVICES
Program only if
Relays and/or
Powerline Carrier
devices are to be
used. See next page.
*
82
CUSTOM ALPHA EDITING:
(Also entered from field
*
56):
See procedure in instructions.
*
83
SEQUENTIAL LEARN MODE
(Also entered from
field
*
56):
See procedure in instructions.
*
89
EVENT LOG 80% FULL RPT CODE
|
*
90
EVENT LOGGING
[3]
0 = None; 1 = Alarm/Alarm Restore;
2 = Trouble/Trouble Restore; 4 = Bypass/Bypass
Restore; 8 = Open/Close.
Example: To select “Alarm/Alarm Restore”, and
“Open/Close”, enter 9 (1 + 8); To select all, enter #15.
Note:
System messages are logged when any non-
zero selection is made.
*
91
OPTION SELECTION (AAV)
[0]
0 = None; 4 = AAV;“0” for UL installations.
*
92
PHONE LINE MONITOR ENABLE
[0]
0 = Not used
1 = Keypad display when line is faulted
2 = Keypad display plus keypad trouble sound
3 = Same as “2”, plus Device #2 STARTS. If either
partition is armed, external sounder activates also.
Note:Ê
Device #2 must either be programmed to be
STOPPED in field
*
80 or STOPPED by Code + # + 8 + 2.
*
93
No. OF REPORTS IN ARMED PERIOD
[0]
0 = 10 Alarm/Alarm Restore Reports; 1 = Unlimited.
“1” for UL installations.
DOWNLOAD INFORMATION (
*
94,
*
95)
*
94
DOWNLOAD PHONE No.
| | | | | | | | | | | | | | |
Enter up to 16 digits, 0–9;
#+11 for '*'; #+12 for '#'; #+13 for
a pause. Do not fill unused spaces. If fewer than 16 digits
entered, exit field by pressing
*
(and press 95, if entering
next field). To clear entries from field, press
*
94
*
.
Note:
In UL installations, down loading may only be
performed if a technician is at the site.
*
95
RING DET COUNT FOR DOWNLOADING[0]
0 = Disable Station Initiated Download; 1–14 = number
of rings (1–9, # +10 =10, # +11 =11, # +12 =12,
# +13 =13, # +14 =14); 15 = answering machine defeat
(# +15 =15)
Note:
Do not enter “0” if using 4285 Voice Module.
*
96
INITIALIZES DOWNLOAD ID, SUBSCRIBER
ACCOUNT No. FOR INITIAL DOWNLOAD:
No data entry required.
*
97
SETS ALL PROGRAM FIELDS TO DEFAULT
VALUES:
No data entry required.
*
98
Exits programming mode and
prevents re-entry
by: Installer Code + 8+ 0 + 0. If
*
98
is used to
exit programming mode, system must be
powered down, and method 1 above used to
enter the programming mode.
*
99
Exits programming mode and
allows re-entry
by: Installer Code + 8 + 0 + 0 or: Power-up, then
press "
*
" and "#" within 50 seconds of power up.