White Rodgers 1F80-224 User Manual

Page 6

Advertising

If the outside temperature is below 50°F, disconnect

If the outside temperature is below 50°F, disconnect
power to the cooling system before programming.

power to the cooling system before programming.

power to the cooling system before programming.
Energizing the air conditioner compressor during

Energizing the air conditioner compressor during

Energizing the air conditioner compressor during
cold weather may cause personal injury or property

cold weather may cause personal injury or property

cold weather may cause personal injury or property
damage.

damage.

▲

CAUTION

1. Move SYSTEM switch to COOL

COOL

COOL position.

2. Follow the procedure for entering your cooling program,

using your selected cooling times and temperatures.

Enter Cooling Program

CHECK YOUR PROGRAMMING

Follow these steps to check your thermostat programming one
final time before beginning thermostat operation.

1. Move SYSTEM switch to HEAT

HEAT

HEAT position.

2. Press PRGM to view the 1st heating period time and

temperature. Each time you press PRGM, the next heating
period time and temperature will be displayed in sequence
(you may change any time or temperature during this proce-
dure).

3. Press RUN.

4. Move SYSTEM switch to COOL

COOL

COOL position.

5. Repeat step 2 to check cooling program.

6. Move SYSTEM switch to HEAT

HEAT

HEAT or COOL

COOL

COOL and press RUN to

begin program operation.

YOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED AND

YOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED AND
READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY!

READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY!

Reset Operation

Reset Operation
If a voltage spike or static discharge blanks out the display or
causes erratic thermostat operation you can reset the thermo-

stat by pressing

and TIME at the same time. This also

resets the factory defaults to the configuration menu and
program. If the thermostat has power, has been reset and still
does not function correctly contact your heating/cooling ser-
vice person or place of purchase.

Batteries

Batteries
For optimum performance, we recommend replacing batteries
once a year with fresh "AA" Energizer

alkaline batteries.

TROUBLESHOOTING

Entering Your Program

Follow these steps to enter the heating and cooling programs
you have selected.

Set Current Time

1. Press TIME button once. The display will show the hour only.

EXAMPLE:

2. Press and hold either

until you reach the correct

hour and AM/PM designation (AM

AM begins at midnight; PM

begins at noon).

3. Press TIME once. The display window will show the minutes

only.

EXAMPLE:

4. Press and hold either

until you reach the correct

minutes.

Enter Heating Program

1. Move the SYSTEM switch to HEAT

HEAT

HEAT.

2. Press PRGM once. Displayed are the currently programmed

start time for the 1st heating

1st heating

1st heating period and the currently

programmed temperature (flashing).

EXAMPLE:

This display window shows that for the 1st weekday period,
the start time is 6:00 AM, and 70° is the programmed
temperature (this example reflects factory preprogramming).

3. Press

to change the displayed temperature to

your selected temperature for the 1st heating program
period.

4. Press TIME once (the programmed time will flash). Press

until your selected time appears. The time will

change in 15 minute increments. When your selected time
is displayed, press TIME again to return to the change
temperature mode.

5. Press PRGM once. The currently programmed start time

and setpoint temperature for the 2nd heating

2nd heating

2nd heating program

period will appear.

6. Repeat steps 3 and 4 to select the start time and heating

temperature for the 2nd heating program period.

7. Repeat steps 3 through 5 for the 2nd, 3rd and 4th heating

program periods. Programming is now complete.

8. When you have completed entering your program, press

RUN.

For Troubleshooting information, see next page

Advertising