ZyXEL Communications ZyXEL Dimension GS-2024 User Manual
Gs-2024, User’s guide
Advertising
Table of contents
Document Outline
- User’s Guide
- Introduction
- Basic Configuration
- Advanced Setup
- VLAN
- Static MAC Forward Setup
- Spanning Tree Protocol
- 10.1 STP/RSTP Overview
- 10.1.1 STP Terminology
- 10.1.2 How STP Works
- 10.1.3 STP Port States
- 10.1.4 Multiple STP
- 10.2 Spanning Tree Protocol Status Screen
- 10.3 Spanning Tree Configuration
- 10.4 Configure Rapid Spanning Tree Protocol
- 10.5 Rapid Spanning Tree Protocol Status
- 10.6 Configure Multiple Spanning Tree Protocol
- 10.7 Multiple Spanning Tree Protocol Status
- Bandwidth Control
- Broadcast Storm Control
- Mirroring
- Link Aggregation
- Port Authentication
- Port Security
- Queuing Method
- Multicast
- 18.1 Multicast Overview
- 18.1.1 IP Multicast Addresses
- 18.1.2 IGMP Filtering
- 18.1.3 IGMP Snooping
- 18.1.4 IGMP Snooping and VLANs
- 18.2 Multicast Status
- 18.3 Multicast Setting
- 18.4 IGMP Snooping VLAN
- 18.5 IGMP Filtering Profile
- 18.6 MVR Overview
- 18.6.1 Types of MVR Ports
- 18.6.2 MVR Modes
- 18.6.3 How MVR Works
- 18.7 General MVR Configuration
- 18.8 MVR Group Configuration
- 18.8.1 MVR Configuration Example
- Authentication & Accounting
- 19.1 Authentication, Authorization and Accounting
- 19.1.1 Local User Accounts
- 19.1.2 RADIUS and TACACS+
- 19.2 Authentication and Accounting Screens
- 19.2.4 Vendor Specific Attribute
- 19.2.5 Tunnel Protocol Attribute
- 19.3 Supported RADIUS Attributes
- 19.3.1 Attributes Used for Authentication
- 19.3.2 Attributes Used for Accounting
- Loop Guard
- IP Application
- Static Route
- Differentiated Services
- DHCP
- 23.1 DHCP Overview
- 23.1.1 DHCP Modes
- 23.1.2 DHCP Configuration Options
- 23.2 DHCP Status
- 23.3 DHCP Relay
- 23.3.1 DHCP Relay Agent Information
- 23.3.2 Configuring DHCP Global Relay
- 23.3.3 Global DHCP Relay Configuration Example
- 23.4 Configuring DHCP VLAN Settings
- 23.4.1 Example: DHCP Relay for Two VLANs
- Management
- Maintenance
- 24.1 The Maintenance Screen
- 24.2 Load Factory Default
- 24.3 Save Configuration
- 24.4 Reboot System
- 24.5 Firmware Upgrade
- 24.6 Restore a Configuration File
- 24.7 Backup a Configuration File
- 24.8 FTP Command Line
- 24.8.1 Filename Conventions
- 24.8.2 FTP Command Line Procedure
- 24.8.3 GUI-based FTP Clients
- 24.8.4 FTP Restrictions
- Access Control
- 25.1 Access Control Overview
- 25.2 The Access Control Main Screen
- 25.3 About SNMP
- 25.3.1 SNMP v3 and Security
- 25.3.2 Supported MIBs
- 25.3.3 SNMP Traps
- 25.3.4 Configuring SNMP
- 25.4 SSH Overview
- 25.5 How SSH works
- 25.6 SSH Implementation on the Switch
- 25.6.1 Requirements for Using SSH
- 25.7 Introduction to HTTPS
- 25.8 HTTPS Example
- 25.8.1 Internet Explorer Warning Messages
- 25.8.2 Netscape Navigator Warning Messages
- 25.8.3 The Main Screen
- 25.9 Service Port Access Control
- 25.10 Remote Management
- Diagnostic
- Syslog
- Cluster Management
- MAC Table
- ARP Table
- Configure Clone
- Maintenance
- Troubleshooting & Product Specifications
- Appendices and Index