ZyXEL Communications GS-3012F Series User Manual
User’s guide
Advertising
Table of contents
Document Outline
- User’s Guide
- Introduction and Hardware Overview
- Basic Settings
- Advanced Settings
- VLAN
- Static MAC Forward Setup
- Filtering
- Spanning Tree Protocol
- 11.1 STP/RSTP Overview
- 11.1.1 STP Terminology
- 11.1.2 How STP Works
- 11.1.3 STP Port States
- 11.1.4 Multiple RSTP
- 11.2 Spanning Tree Protocol Main Screen
- 11.3 Configure Rapid Spanning Tree Protocol
- 11.4 Rapid Spanning Tree Protocol Status
- 11.5 Configure Multiple Rapid Spanning Tree Protocol
- 11.6 Multiple Rapid Spanning Tree Protocol Status
- Bandwidth Control
- Broadcast Storm Control
- Mirroring
- Link Aggregation
- Port Authentication
- Port Security
- Classifier
- Policy Rule
- Queuing Method
- Multicast
- 21.1 Multicast Overview
- 21.1.1 IP Multicast Addresses
- 21.1.2 IGMP Filtering
- 21.1.3 IGMP Snooping
- 21.2 Multicast Status
- 21.3 Multicast Setup
- 21.4 IGMP Filtering Profile
- 21.5 MVR Overview
- 21.5.1 Types of MVR Ports
- 21.5.2 MVR Modes
- 21.5.3 How MVR Works
- 21.6 General MVR Configuration
- 21.7 MVR Group Configuration
- 21.7.1 MVR Configuration Example
- DHCP Relay
- Static Routing and Management
- Routing Protocol
- Maintenance
- 24.1 Maintenance
- 24.2 Load Factory Defaults
- 24.3 Save Configuration
- 24.4 Reboot System
- 24.5 Firmware Upgrade
- 24.6 Restore a Configuration File
- 24.7 Backing Up a Configuration File
- 24.8 Command Line FTP
- 24.8.1 Filename Conventions
- 24.8.2 FTP Command Line Procedure
- 24.8.3 GUI-based FTP Clients
- 24.8.4 FTP Restrictions
- Access Control
- 25.1 About Access Control
- 25.2 Access Control Overview
- 25.3 About SNMP
- 25.3.1 Supported MIBs
- 25.3.2 SNMP Traps
- 25.3.3 Configuring SNMP
- 25.4 SSH Overview
- 25.5 How SSH works
- 25.6 SSH Implementation
- 25.6.1 Requirements for Using SSH
- 25.7 Introduction to HTTPS
- 25.7.1 HTTPS Example
- 25.7.2 Internet Explorer Warning Messages
- 25.7.3 Netscape Navigator Warning Messages
- 25.7.4 Login Screen
- 25.8 Service Access Control
- 25.9 Remote Management
- Diagnostic
- Syslog
- Cluster Management
- MAC Table
- ARP Table
- Configure Clone
- Commands and Troubleshooting
- Introducing the Commands
- 32.1 Overview
- 32.1.1 Switch Configuration File
- 32.2 Accessing the CLI
- 32.2.1 Access Priority
- 32.2.2 The Console Port
- 32.2.3 Telnet
- 32.3 The Login Screen
- 32.4 Command Syntax Conventions
- 32.5 Getting Help
- 32.5.1 List of Available Commands
- 32.5.2 Detailed Command Information
- 32.6 Privilege Levels
- 32.7 Command Modes
- 32.8 Using Command History
- 32.9 Saving Your Configuration
- 32.9.1 Logging Out
- 32.10 Command Summary
- 32.10.1 User Mode
- 32.10.2 Enable Mode
- 32.10.3 Configure Mode
- 32.10.4 config-vlan Commands
- 32.10.5 interface port-channel Commands
- 32.10.6 mvr Commands
- Command Examples
- 33.1 Overview
- 33.2 show Commands
- 33.2.1 show system-information
- 33.2.2 show hardware-monitor
- 33.2.3 show ip
- 33.2.4 show logging
- 33.2.5 show interface
- 33.2.6 show mac address-table
- 33.3 ping
- 33.4 traceroute
- 33.5 Enabling RSTP
- 33.6 Configuration File Maintenance
- 33.6.1 Backing up Configuration
- 33.6.2 Restoring Configuration
- 33.6.3 Using a Different Configuration File
- 33.6.4 Resetting to the Factory Default
- 33.7 Example no Commands
- 33.7.1 no mirror-port
- 33.7.2 no trunk
- 33.7.3 no port-access-authenticator
- 33.7.4 no ssh
- 33.8 interface Commands
- 33.8.1 interface port-channel
- 33.8.2 bpdu-control
- 33.8.3 broadcast-limit
- 33.8.4 bandwidth-limit
- 33.8.5 mirror
- 33.8.6 gvrp
- 33.8.7 ingress-check
- 33.8.8 vlan-trunking
- 33.8.9 weight
- 33.8.10 egress set
- 33.8.11 qos priority
- 33.8.12 name
- 33.8.13 speed-duplex
- IEEE 802.1Q Tagged VLAN Commands
- 34.1 IEEE 802.1Q Tagged VLAN Overview
- 34.2 VLAN Databases
- 34.2.1 Static Entries (SVLAN Table)
- 34.2.2 Dynamic Entries (DVLAN Table)
- 34.3 Configuring Tagged VLAN
- 34.4 Global VLAN1Q Tagged VLAN Configuration Commands
- 34.4.1 GARP Status
- 34.4.2 GARP Timer
- 34.4.3 Show GVRP
- 34.4.4 Enable GVRP
- 34.4.5 Disable GVRP
- 34.5 Port VLAN Commands
- 34.5.1 Set Port VID
- 34.5.2 Set Acceptable Frame Type
- 34.5.3 Enable or Disable Port GVRP
- 34.5.4 Modify Static VLAN
- 34.5.5 Delete VLAN ID
- 34.6 Enable VLAN
- 34.7 Disable VLAN
- 34.8 Show VLAN Setting
- Troubleshooting
- Introducing the Commands
- Appendices and Index