Zanussi ZWN 6120 L - Manual (Page 8)

The selector dial can be turned either clockwise or coun-
terclockwise. Turn to position to reset programme/
Switching the machine off.
At the end of the programme the selector dial must be
turned to position , to switch the machine off.
Caution! If you turn the programme selector dial to
another programme when the machine is working,
the red pilot light of button 5 will blink 3 times to indicate
a wrong selection. The machine will not perform the new
selected programme.
Select the spin speed or Rinse Hold by pressing
button 2
When selecting a programme, the appliance proposes au-
tomatically the maximum spin speed provided for that
programme. (See "Washing programmes" for the maxi-
mum allowed spin speed).
Press this button repeatedly to change the spin speed, if
you want your laundry to be spun at a different speed. The
relevant pilot light illuminates.
Select the available options by pressing buttons 3
and 4
Depending on the programme, different functions can be
combined. These must be selected after choosing the de-
sired programme and before starting the programme.
When these buttons are pressed, the corresponding pilot
lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected, the inte-
grated red pilot light of the button 5 flashes for 3 times.
For the compatibility among the washing pro-
grammes and the options see chapter «Washing
Programmes».
Select the Delay Start by pressing button 6
Before you start the programme, if you wish to delay the
start, press the button 6 repeatedly, to select the desired
delay. The relevant light illuminates.
You must select this option after you have set the pro-
gramme and before you start the programme.
You can cancel or modify the delay time at any moment,
before you press button 5.
Selecting the delayed start:
1. Select the programme and the required options.
2. Select the delay start by pressing the button 6.
3. Press button 5:
– the machine starts its hourly countdown.
– The programme will start after the selected delay
has expired.
Cancelling the delayed start after having started the pro-
gramme:
1. Set the washing machine to PAUSE by pressing but-
ton 5.
2. Press button 6 once, the light relevant to the selected
delay goes off
3. Press button 5 again to start the programme.
The Delay Start can not be selected with DRAIN pro-
gramme.
Important! The selected delay can be changed only after
selecting the washing programme again.
The door will be locked throughout the delay time. If you
need to open the door, you must set the machine to
PAUSE (by pressing the button 5) and then wait a few
minutes. After you have closed the door, press the button
5 again.
Start the programme by pressing button 5
To start the selected programme, press the button 5, the
corresponding green pilot light stops blinking. The pilot
light corresponding to the running phase illuminates. The
appliance starts operating and the door is locked.
To interrupt a programme which is running, press the but-
ton 5: the corresponding green pilot light starts blinking.
To restart the programme from the point at which it was
interrupted, press the button 5 again. If you have chosen a
delayed start, the machine will begin the countdown.
If an incorrect option is selected, the red pilot light of the
button 5 blinks 3 times.
Interrupting a programme
Press the button 5 to interrupt a programme which is run-
ning, the corresponding green pilot light starts blinking.
Press the button again to restart the programme.
Cancelling a programme
Turn the selector dial to to cancel a programme which
is running. Now you can select a new programme.
Opening the door
After the programme has started the door is locked. If, for
any reason, you need to open it, set firstly the machine to
PAUSE by pressing the button 5. After a few minutes it
will be possible to open the door.
If the door remains locked, this means that the machine is
already heating or that the water level is too high. In any
case, do not try to force the door!
8