Yamaha NOT FOND DSP-Z11 - Manual (Page 89)

Graphical user interface (GUI) menu
89
En
Ad
v
a
nce
d
Op
eratio
n
Auto (Automatic audio delay adjustment)
Use this feature to make fine adjustments of the audio and video
synchronization when you set “HDMI Auto” to “On”.
Control range: 0 to 240 ms
Control step: 1 ms
y
“offset” indicates the difference between the value of the audio delay that this unit sets
automatically and the value of the audio delay that you set in “HDMI Auto”. This unit
stores the value of “Offset” and applies the value to other automatic lip sync compatible
video monitors.
Manual (Manual audio delay adjustment)
Use this feature to adjust the delay of the sound output manually to
synchronize audio with video images when you set “HDMI Auto”
to “Off”.
Control range: 0 to 240 ms
Control step: 1 ms
■ Pure Direct (Pure Direct)
Use this feature to select whether this unit outputs the video signals
when this unit is in the Pure Direct mode.
You cannot use the GUI menu while this unit is in the Pure Direct mode even if “Pure
Direct” is set to “Video On”.
■ Channel Mute (Channel mute)
Use this feature to mute specific speaker channels.
Mode (Mode)
Use this feature to activate or deactivate the “Channel Mute” setting
for each speaker.
Each speaker settings
Select whether this unit mutes each speaker channel when you set
“Mode” to “Enable”.
Use this menu to adjust the video parameters.
Use the “VIDEO” in “INITIALIZE” to set the parameters in “Manual Setup (Video)”
(except “Short Message” and “On Screen”) to the factory presets (see page 120).
■ Conversion (Video conversion)
Use this feature to activate or deactivate the video scaling as well as
the HDMI up-conversion of the analog video signals input at the
VIDEO, S VIDEO, and COMPONENT VIDEO jacks.
• For optimal video performance, THX Ltd. recommends that you set “Conversion” to
“Off” to allow video signals to pass through the system without processing (e.g.,
video signals input at the COMPONENT VIDEO jacks are output at the
COMPONENT VIDEO MONITOR OUT jacks without any processing).
• The converted video signals are only output at the MONITOR OUT jacks. When
recording a video source, you must make the same type of video connections between
each component.
• When composite video or S-video signals from a VCR are converted into component
video signals, the picture quality may suffer depending on your VCR.
• If “Conversion” is set to “Off”, the “Component I/P”, “HDMI Resolution”, “HDMI
Processing”, “HDMI Aspect”, and “Short Message” features are deactivated.
• Set “Conversion” to “On” to display the short message.
• This unit does not convert 480 line video signals and 576 line video signals
interchangeably.
• The analog component video signals with 480i (NTSC)/576i (PAL) of resolution are
converted into the S-video or composite video signals and output at the S VIDEO
MONITOR OUT and VIDEO MONITOR OUT jacks.
• Even when “Conversion” is set to “On”, HDMI digital signals are not converted to
analog video signals.
• This unit cannot convert the signals input at the VIDEO or S VIDEO jacks and
displays the video images correctly depending on the input source component and the
source played on the component. In such cases, set “Conversion” to “Off”.
• When non-standard video signals (such as video signals from a video game console)
are input, this unit does not display short messages in the video monitor even if
“Conversion” is set to “On”.
• When the analog component video signals with 480p/576p of resolution are input at
the COMPONENT VIDEO jacks and the video monitor is connected to the VIDEO
MONITOR OUT or S VIDEO MONITOR OUT jack on this unit, the GUI screen is
not displayed in the video monitor.
Choice Descriptions
Off Select this setting if the connected video monitor is
compatible with the automatic lip sync. Use “Auto” to
make fine adjustments of the audio and video
synchronization.
On Select this setting if the video monitor is not compatible
with the automatic lip sync or you do not want to use the
automatic lip sync. Use “Manual” to adjustment the
audio and video synchronization.
Choice Functions
Video Off Does not output video signals.
Video On Outputs video signals. For the better sound quality, this
unit only activates the limited video features.
Note
Choice Functions
Disable Deactivates the “Channel Mute” function.
Enable Activates the “Channel Mute” function.
Choice Functions
Mute On Mutes the selected speaker channel.
Mute Off Does not mute the selected speaker channel.
Channel Mute Speaker channel
Front L Front left
Front R Front right
Center Center
Surround L Surround left
Surround R Surround right
Surround Back L Surround back left
Surround Back R Surround back right
Front Presence L Front presence left speaker
Front Presence R Front presence right speaker
Rear Presence L Rear presence left speaker
Rear Presence R Rear presence right speaker
Subwoofer L Subwoofer left
Subwoofer R Subwoofer right
Manual Setup (Video)
Note
Choice Functions
On Converts composite, S-video, and component video
signals interchangeably and up-converts composite, S-
video, and component video signals to HDMI video
signals.
Off Does not convert any signals.
Notes