Festool PSBC 400 EB CARVEX - Manual (Page 21)

CARVEX
21
GB
– If LiIon battery packs are to be stored for
long periods without use, they should be
charged to 40 % capacity (approx. 15 mins.
charging period).
10 Accessories
Use only original Festool accessories and Fes-
tool consumable material intended for this ma-
chine because these components are designed
specifically for the machine. Using accessories
and consumable material from other suppliers
will most likely affect the quality of your work-
ing results and limit any warranty claims. Ma-
chine wear or your own personal workload may
increase depending on the application. Protect
yourself and your machine, and preserve your
warranty claims by always using original Fes-
tool accessories and Festool consumable mate-
rial!
The order numbers of the accessories and tools
can be found in the Festool catalogue or on the
Internet under "www.festool.com".
10.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli-
cations that are specially designed for your Fes-
tool jigsaw.
10.2 Sawing with special base runners
The special base runners protect high-quality
surfaces against scratches and scores.
X Press in the base runner at position [7-1] .
X At the same time, push the base runner for-
wards.
X Mount another base runner and push it to
the rear until it engages.
10.3 Sawing with the angle table
The angle table WT-PS 400 is used for sawing in-
terior and exterior angles up to 45° and pipes.
Dust extraction is not possible when
sawing with the angle table!
Installing the angle table
X Remove the saw table [1-10] , (see chapter 7.4).
X Position the angle table against the saw ta-
ble support.
X Close the change lever [1-8] .
Ensure that the angle table is firmly seated in
the guide.
Setting the angle
X Turn the adjusting wheel [8-1] to set the de-
sired angle.
You can set the values -45°, 0° and +45° using
the scale
[8-2] .
L For 90° cuts, we recommend setting the an-
gle table to a small negative degree value to
guarantee stable running.
10.4 Sawing with the adaptation table
The adaptation table ADT-PS 400 is used for fit-
ting your jigsaw on the Festool guide rail and
the circle cutter KS-PS 400.
Installing the adaptation table
X Remove the saw table [1-10] , (see chapter
7.4).
X Mount the adaptation table [9-1] on the saw
table support.
X Close the change lever [1-8] .
Ensure that the adaptation table is firmly seat-
ed in the guide.
L Use the extractor connector
[1-7] also with
the adaptation table.
Adaptation to the guide rail FS 2
Using the Festool guide system FS 2 (Fig.
[10] ) makes it easier to produce straight and
precise cuts, in particular, with material thick-
nesses up to 20 mm.
X Place the jigsaw with attached adaptation
table
[9-1] on the guide rail.
Adaptation to the circle cutter
The circle cutter can be used to create circular
cuts with a diameter between 120 and 3000
mm. The circle cutter can be installed from both
sides on the adaptation table.
X Place the jigsaw with attached adaptation
table on the adapter
[11-1] on the circle
cutter.
X Insert the centring mandrel [11-2] in the
hole [11-4] on the circle cutter aligned with
the saw blade.
X Clamp the measuring tape to the circle cut-
ter using the rotary knob
[11-5] .
Angle table position Application
Picture [8A] Angle, interior angle
Picture [8B] Angle
Picture [8C] Exterior angle, pipes
WARNING
Sawing cutting depths
Risk of injury
X Select the saw blade length and cutting
depth so that the saw blade always stays
in the workpiece.