Fein ABS_18C - Manual (Page 15)

15 en
For your safety.
Read all safety warnings and all
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
ABS14, ABS18:
Hand-held cordless drill/driver for screwing in and
unscrewing screws and nuts, and for drilling and screw-
driving in metal, wood, plastic, ceramics, as well as for
tapping in weather-protected environments without
water supply using the application tools and accessories
recommended by FEIN.
ASB14, ASB18:
Hand-held cordless hammer drill for screwing in and
unscrewing screws and nuts, and for drilling and screw-
driving in metal, wood, plastic, ceramics, as well as for
tapping and impact drilling in concrete, stone and bricks
in weather-protected environments without water sup-
ply using the application tools and accessories recom-
mended by FEIN.
Special safety instructions.
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a “live” wire may
make exposed metal parts of the power tool “live” and
could give the operator an electric shock.
Beware of any concealed electric cables, gas or water
conduits. Check the working area before commencing
work, e.g. with a metal detector.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses.
Where appropriate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.
Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
Secure the work piece firmly. A work piece that is
gripped tightly in a clamping device or vice, is more
secure than if held by hand.
Hold the power tool firmly. High reaction torque can
briefly occur.
Reduce torque
Increase torque
Character Unit of measurement,
international Unit of measurement,
national Explanation
U V V DC voltage
f Hz Hz Frequency
n
0
/min, min -1 , rpm, r/min rpm No-load speed (with fully charged battery)
n
S
/min, min -1 /min Impact rate
M... Nm Nm Torque (hard/soft screwdriving application)
Ø mm mm Diameter of a round part
L
pA
dB dB Sound pressure level
L
wA
dB dB Sound power level
L
pCpeak
dB dB Peak sound pressure level
K... Uncertainty
m/s 2 m/s 2 Vibrational emission value according to
EN 60745 (vector sum of three directions)
h,D
m/s
2
m/s
2
Mean vibrational value for drilling in metal
h,ID
m/s 2 m/s 2 Mean vibrational value for impact drilling in
concrete
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
Basic and derived units of measurement from
the international system of units SI.
Symbol, character Explanation
WARNING
OBJ_BUCH-0000000105-001.book Page 15 Thursday, April 4, 2013 10:23 AM