Fein WPO 14-15E - Manual (Page 18)

18 en
For your safety.
Read all safety warnings and all instruc-
tions. Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
hand-guided polisher for dry polishing, sanding with
sanding discs and brushing surfaces of metal, stone, plas-
tic, wood, composite materials, paint/varnish, filler and
similar materials in weather-protected environments
using the application tools and accessories recommended
by FEIN.
This machine is also intended to be powered by a.c. gen-
erators with sufficient power output that correspond
with ISO 8528, design class G2. Compliance with this
Standard in particular is not given when the so-called dis-
tortion factor exceeds 10%. When in doubt, inform
yourself about the generator in use.
Safety warnings common for sanding, sanding with
sanding sheets, working with wire brushes,
polishing and cut-off grinding
This power tool is intended to function as a sander, wire
brush or polisher. Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Operations such as grinding or cutting-off are not recom-
mended to be performed with this power tool. Operations
for which the power tool was not designed may create a
hazard and cause personal injury.
Do not use accessories which are not specifically designed
and recommended by the tool manufacturer. Just because
the accessory can be attached to your power tool, it does
not assure safe operation.
The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and fly
apart.
The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
The arbor size of wheels, flanges, backing pads or any other
accessory must properly fit the spindle of the power tool.
Accessories with arbor holes that do not match the
mounting hardware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss of control.
Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and
cracks, backing pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power tool or accessory
is dropped, inspect for damage or install an undamaged
accessory. After inspecting and installing an accessory,
Character Unit of measure,
international Unit of measure,
national Explanation
n /min rpm Rated speed
V V Rated voltage
P
1
W W Power input
P
2
W W Output
f Hz Hz Frequency
M… mm mm Size of metric thread
L
wA
dB dB Sound power level
L
pA
dB dB Sound pressure level
L
pCpeak
dB dB Peak sound pressure level
K… Uncertainty
m/s
2
m/s
2
Vibration emission value (triax vector sum) deter-
mined according to EN 60745
m/s
2
m/s
2
Mean vibrational value for polishing
m/s
2
m/s
2
Mean vibrational value for sanding with sanding
sheet
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
Basic and derived units of measure from the inter-
national system of units
SI.
h,P
h,DS
WARNING
3 41 01 113 06 0.book Seite 18 Dienstag, 8. Dezember 2009 7:51 07