STIEBEL ELTRON SH A с 01.03.2009 - Manual (Page 16)

Ĝō ’Z+  qqqĪZ`.
<é<`VHCĪHB
HC`C`Z’HTV`.HC
&CV< .C%HVB`.HC
1. General information
1.1 Document information
The chapter Operation is intended for the equipment user and the
heating contractor.
The chapter Installation is intended for contractors.
Please read!
Read these instructions carefully before using the
appliance and retain them for future reference. If the
appliance is passed on to a third party please hand
these instructions to the new user.
1.2 Key to symbols
Symbols in these installation instructions:
In this documentation you will come across symbols and highlights.
These have the following meaning:
Risk of injury!
Information concerning possible risk of injury.
Danger of electrocution!
Risk of scalding or burning!
!
Possible damage!
Information concerning damage to the appliance,
environmental damage or material losses.
Please read!
Text next to this symbol is particularly important.
» The " » " symbol indicates that you have to do something. The
action you need to take is described step-by-step.
Symbols on the appliance:
Disposal!
Appliances with this marking are not suitable for
general waste disposal, and should therefore be
disposed of separately.
Units of measurement
All measurements are given in mm unless stated otherwise.
OPERATION ____________________________________________ 16
1. General information __________________________________________ 16
1.1 Document information ___________________________________________ 16
1.2 Key to symbols _____________________________________________________ 16
2. Safety __________________________________________________________ 17
2.1 Intended use ________________________________________________________ 17
2.2 Safety information ________________________________________________ 17
2.3 CE-designation _____________________________________________________ 17
2.4 Test symbols ________________________________________________________ 17
3. Appliance description ________________________________________ 17
4. Operation _____________________________________________________ 17
4.1 Setting temperatures _____________________________________________ 17
4.2 DHW display ________________________________________________________ 17
5. Cleaning, care and maintenance ____________________________ 18
6. What to do if ... _______________________________________________ 18
6.1 ... the appliance develops faults ________________________________ 18
INSTALLATION _________________________________________ 19
7. Safety __________________________________________________________ 19
7.1 General safety instructions ______________________________________ 19
7.2 Instructions, standards and regulations ______________________ 19
7.3 Water
installation__________________________________________________ 19
8. Appliance description ________________________________________ 19
8.1 Standard delivery __________________________________________________ 19
8.2 Special accessories ________________________________________________ 19
9. Installation ____________________________________________________ 21
9.1 Place of installation _______________________________________________ 21
9.2 Installation
__________________________________________________________ 21
9.3 Alternative installation methods _______________________________ 22
10. Commissioning ________________________________________________ 22
11. Taking the appliance out of use _____________________________ 22
12. Recommissioning _____________________________________________ 22
13. Appliance handover __________________________________________ 22
14. Troubleshooting_______________________________________________ 23
14.1 Fault table ___________________________________________________________ 23
15. Maintenance___________________________________________________ 23
15.1 Check the safety assembly _______________________________________ 23
15.2 Controller-limiter combination immersion depths _________ 23
15.3 Draining the appliance ___________________________________________ 23
15.4 Checking the protective anode __________________________________ 24
15.5 Descaling the flange ______________________________________________ 24
15.6 Anti-corrosion protection ________________________________________ 24
16. Specification ___________________________________________________ 24
16.1 Dimensioned drawing ____________________________________________ 24
16.2 Connections _________________________________________________________ 25
16.3 Wiring diagrams and connections _____________________________ 25
16.4 Hydraulic schematic diagram ___________________________________ 26
16.5 Specification ________________________________________________________ 26
16.6 Fault conditions ____________________________________________________ 27
CUSTOMER SERVICE AND WARRANTY _______________ 28
ENVIRONMENT AND RECYCLING ______________________ 28