Candy CNE103T-04S - Manual (Page 14)

Please note:
It is normal for the programme selector dial to move only from one stage of washing programme to another
and not show any movement in-between – so at certain periods, the dial will stay still.
An electronic device is controlling the exact movement of the timer.
27
CHAPTER 12
EN
FAULT
If the fault should persist, contact a Technical Assistance Centre. For prompt servicing, give the model of the
washing machine, to be found on the label placed on the cabinet inside of the porthole or on the guarantee
certificate.
Important
1 The use of environment friendly detersives without phosphates may produce the following effects:
- The discharge rinse water may result cloudier due to the presence of zeolites in suspension. This does not
compromise the efficiency of the rinses.
- The presence of white powder (zeolites) on the washing at the end of the washing cycle. This does not
remain incorporated in the fabric and does not alter the colour.
- The presence of foam in the last rinse water which is not necessarily a sign of inadequate rinsing.
- The non-ionic surface-active agents present in the composition of washing machine detersives are often
difficult to remove from the washing itself and, even in small quantities, may produce visible signs of the
formation of foam.
- Carrying out further rinses, in cases such as this, is not useful.
2 If your washing machine fails to function, carry out the above-mentioned checks before calling the Technical
Assistance Service.
1. Does not function
on any
programme
2. Does not load
water
3. Does not discharge
water
4. Water on floor
around washing
machine
5. Does not spin
6. Strong vibrations
during spin
Mains plug not plugged in
Mains switch not on
No power
Electric circuit fuses failure
Load door open
See cause 1
Inlet tap turned off
Timer not set correctly
Discharge tube bent
Odd material blocking filter
Leak from the washer between the tap
and inlet tube
The washing machine has not
discharged water
“No spin” setting (some models only)
Washing machine not perfectly level
Transport bracket not removed
Washing load not evenly distributed
Insert plug
Turn on mains switch
Check
Check
Close load door
Check
Turn on water inlet tap
Set timer on correct position
Straighten discharge tube
Check filter
Replace washer and tighten the tube
on the tap
Wait a few minutes until the machine
discharges water
Turn the programme dial onto spin
setting
Adjust special feet
Remove transport bracket
Distribute the washing evenly
CAUSE REMEDY
26
EN
FILTER CLEANING
The washing-machine is
equipped with a special filter to
retain large foreign matter which
could clog up the drain, such as
coins, buttons, etc. These can,
therefore, easily be recovered.
The procedures for cleaning the
filter are as follows:
● Ease off the base as shown in
fig.
● Use the base as a tray to
collect leftover water in filter.
● Turn the filter anticlockwise till it
stops in vertical position.
● Remove and clean.
● After cleaning, replace by
turning the notch on the end of
the filter clockwise. Then follow all
procedures described above in
reverse order.
ATTENTION: IF THE FILTER
NEEDS CLEANING WHILE
THERE IS WASHING STILL IN
THE DRUM, FOLLOW THE
INSTRUCTIONS ON THE
FOLLOWING PARAGRAPH TO
EMPTY THE WATER. THIS WILL
PREVENT EXCESSIVE LOSS OF
WATER VIA THE FILTER.
REMOVALS OR LONG PERIODS
WHEN THE MACHINE IS LEFT
STANDING
For eventual removals or when
the machine is left standing for
long periods in unheated rooms,
the drain hose should be
emptied of all remaining water.
The appliance must be switched
off and unplugged. A bowl is
needed. Detach the drainage
hose from the clamp and lower it
over the bowl until all the water is
removed.
Repeat the same operation with
the water inlet hose.
ES
LIMPIEZA FILTRO
La lavadora está dotada de un
filtro especial que retiene los
residuos de tamaño más grande
que podrían obstruir la
descarga (monedas, botones,
etc) y que de esta manera se
pueden recuperar fácilmente.
Cuando sea necesario limpiar el
filtro seguir los siguientes pasos:
● Suelte el zócalo como se
indica en la figura.
● Utilizar el zócalo para recoger
el agua residual del filtro.
● Gire el filtro en sentido
contrario a las agujas del reloj
hasta que haga tope en
posición vertical.
● Extráigalo y limpielo.
● Después de haberlo limpiado
vuelva a montarlo siguiendo las
operaciones en sentido
contrario a la descripción
precedente.
ATENCIÓN:
EN EL CASO DE QUE LA
LAVADORA NO TUVIERA QUE
EVACUAR EL AGUA, ANTES
DE PROCEDER A LA LIMPIEZA
DEL FILTRO, VACIAR EL
TAMBOR DEL AGUA
RESIDUAL SIGUIENDO LAS
INDICACIONES DETALLADAS
EVITANDO UNA PÉRDIDA
EXCESIVA DE AGUA EN EL
MOMENTO DE EXTRAER EL
FILTRO.
TRASLADOS O LARGOS
PERÍODOS DE INACTIVIDAD DE LA
MÁQUINA
En eventuales traslados o en
caso que la máquina estuviese
inactiva durante largo período
de tiempo en lugares fríos, hay
que vaciar completamente
todo residuo de agua en los
tubos.
Estando desconectada suelte el
tubo de la abrazadera y dirijalo
hacia abajo, en el cubo, hasta
conseguir la salida completa del
agua.
Finalizada la operación, repita
los pasos en sentido contrario.