Naxa NPB-256 User Manual
Page 3
PLAY THE RADIO
NOTES:
HANDLE AND MAINTAIN A COMPACT DISC.
1. Slide the FUNCTION switch to the RADIO position, the POWER Indicator will light up.
2. Select the desired band with the BAND switch.
3. Tune to the desired station by rotating the TUNING control. (Move the control back and forth
until you get the strongest clearest sound).
4. The built-in AM (MW) antenna and external FM TELESCOPIC ANTENNA are directional.
When receiving an FM broadcast, fully extend the TELESCOPIC ANTENNA and
position for the best reception.
For AM (MW) broadcasts, rotate the whole set until the best reception is heard.
5. Adjust the volume level to a comfortable listening level.
6. To turn off the radio, slide the FUNCTION switch to the OFF position.
If a particular FM (STEREO) station is weak, or you hear too much background
noise, try moving the position of the band selector switch to the FM (MONO)
position. This can often result in a much clearer reception.
When the band selector switch is set to FM STEREO and a stereo broadcast is
being received, the FM STEREO indicator will be lit.
Follow the instructions below to handle and maintain your disc in order
that long time and trouble free performance can possibly be obtained:
Ensure not to caress the rain bow side of the disc; handle the
disc by the edge.
Long time exposure to sunshine, high temperatures and
humidity will damage the disc. Keep the storage area clean.
Avoid sticking labels on both sides of a disc. Writing with pointed
articles on the disc should be strictly avoided.
Clean the disc wiping the centre and then working out to the
edge with a dry & soft cloth or a disc brush. Avoid any cleansing
lotion or chemical eradicator.
Store them in their cases when they are not to be used.
=
=
=
=
=
=
=
=
=
LOAD A DISC
NOTE:
NOTE:
REMOVE A DISC
1. Slide the FUNCTION switch to the CD/MP3 position.
If slide the FUNCTION switch to CD/MP3 position, please make sure other
external devices should be disconnected.
2. Open the CD door.
3. Insert a disc with the label side facing upward (if the disc is upside down, the display will
show "NO DISC").
4. Close the CD door by hand.
Never touch the laser lens inside the CD compartment. If it ever gets dirty, clean it
with a CD cleaner disc.
1. Make sure the CD/MP3 disc is not playing. If it is, press the CD STOP button.
2. Open the CD door.
3. Gently remove the disc.
4. Close the CD door by hand.
5. Replace the disc in its protective storage box.
HANDLE DISC ONLY AS SHOWN
CLEAN FROM CENTER TO EDGE
DO NOT STORE NEAR HEAT
PLAY A CD
EQ SELECTION
SKIP TRACKS AND SEARCH FOR A SPECIFIC POINT TO PLAY
PROGRAMMED PLAY
REPEAT A SINGLE TRACK
1. Make sure the power is connected, slide the FUNCTION switch to CD/MP3 position,
POWER indicator will light.
2. Load a disc into the CD compartment. Close the CD door, the disc will begin to spin.
3. Adjust the VOLUME to the desired volume level.
4. To stop playing temporarily, press the PLAY/PAUSE button.
The elapsed time of the current track flashes and an icon of "PAUSE" appears on the
bottom of the LCD to indicate the player is in pause mode.
Resume normal play by pressing PLAY/PAUSE button again.
5. To stop playing, press the STOP button. The total tracks' number and whole playing time
with an icon "STOP" on the bottom will be shown on the display.
6. To turn off the player, slide the FUNCTION switch to OFF position.
Press EQ/Program button continuously during disc playback mode to select EQ sound
effects among NORMAL, POP, ROCK, CLASSIC, JAZZ and BASS.
1. Press once the SKIP/SEARCH up button in music play to skip to the next track. To skip
to a specific track ahead, press this button several times.
2. Press once the SKIP/SEARCH down button in music play to skip to last track. To skip to
a specific track at back, press this button several times.
3. Press +10/ALBUM button once in play to skip to the track 10 tracks ahead, twice to skip
to the track 20 tracks ahead. You can reach the last track of the disc using this button.
4. Hold the SKIP/SEARCH up button in music play to search forward at quick rate for a
Specific point to play.
5. Hold the SKIP/SEARCH down button in music play to search backward at quick rate for
a specific point to play.
Programmed play is that tracks on the disc can be edited for playback in a preferred order
with the use of PROGRAM button.
In CD stop mode, press EQ/PROGRAM button once, "PROG" shows in the LCD with a
flickering track number and the program sequence indication "P-01", select the first track to
be programmed using SKIP/SEARCH buttons, and press EQ/PROGRAM button again to
store and advance to the next programming step. The program sequence indication
changes to "P-02" waiting for your next input.
Repeat the steps above to program more tracks. A maximum of 20 tracks can be
programmed in memory in a preferred order.
Press PLAY/PAUSE button to begin programmed play in the preferred order after you are
done with programming. The player stops automatically after all programmed tracks are
played.
You may press STOP button to terminate programmed playback. In program stop mode,
press STOP button again to clear the programming; press PLAY/PAUSE button to begin
the programmed playback with the programming order identical with the previous one done.
To repeat a preferred track in playback, press MODE button once, the LCD shows the icon
for single track repeat. Then select the preferred track using SKIP/SERCH buttons or
+10/ALBUM button. The player will repeat the chosen track until you press STOP button.
4
5