Banks Power Ford Trucks: (Gas ’04 - 08 F-150 V6 & V8) Exhaust- Monster Exhaust, Dual out the back exit '04-10 F-150 4.2L, 4.6L & 5.4L (Non-Heritage models) User Manual
Page 8
8
96317 v.5.0
system, the factory muffler front
rubber hanger will be removed for Std.
Cab Medium (6.5’) Bed and Ext. Cab
Short (5.5’) Bed models. remove the
factory M8x1.25 bolt on the rubber
muffler hanger, and remove the rubber
hanger from the vehicle (see Figure 3).
7.
FOR 2009-2010 SuPERCREw CAB
MODELS ONLY, Install a 2
1
⁄
2
” clamp
onto the outlet of the factory pipe.
Install the Banks intermediate pipe into
the factory intermediate pipe outlet.
Lightly tighten the 2
1
⁄
2
” clamp.
FOR ALL OTHER MODELS, Install a
2
1
⁄
2
” clamp onto the inlet of the Banks
intermediate pipe. Install the Banks
intermediate pipe onto the factory
Y-pipe outlet. orient the pipe onto
the locating pin and lightly tighten the
2
1
⁄
2
” clamp (see Figure 4).
8.
FOR 2009-2010 SuPERCREw CAB
MODELS ONLY, install the 3” hanger
clamp onto the muffler inlet. The
Hanger pin should face the front of the
vehicle. Install the hanger pin into the
corresponding hanger. Install Banks
Muffler inlet onto the intermediate
pipe and lightly tighten the 3” hanger
clamp.
FOR ALL OTHER MODELS, install a 3”
clamp onto the muffler inlet. Install
the Banks Muffler inlet (Note the
inlet labeling of the muffler) onto the
intermediate pipe and lightly tighten
the 3” clamp.
9.
Install a 3” clamp on the Banks
Muffler outlet. Start the Y-pipe hanger
pin into the corresponding vehicle
rubber hanger. Install Y-pipe into the
Banks Muffler outlet (see Figure 5).
NOTE: Install the rubber hanger pins to
the vehicle frame if previously removed.
10.
FOR TRuCK MODELS wITH
STANDARD TOw HITCH PACKAgE,
on
the left inside of the bumper, remove
the two (2) bumper upper retaining
nuts from the studs. Install the Left
Banks hanger bracket such that it is
parallel with the ground. reinstall the
two (2) factory bumper nuts over the
bracket and torque to 85 ft-lbs. repeat
this process for mounting the right
hanger bracket. See Figure 6.
FOR TRuCK MODELS wITH HEAvY
DuTY TOw HITCH PACKAgE ONLY,
Install the supplied hanger bracket on
the rear driver-side frame rail using the
supplied hardware. Be sure the hanger
pin is align parallel to the frame rail
and torque the hardware to 48ft-lbs.
repeat this process for mounting the
right hanger bracket. See Figure 7.
11.
Install the two (2) supplied rubber
hangers onto the two (2) Banks hanger
brackets.
12.
Install a 3” clamp onto each
Y-pipe outlet. Install the driver-side
tailpipe into the top Y-pipe outlet and
hand tighten the clamp.
13.
Install the passenger-side tailpipe
into the lower Y-pipe outlet and hand
tighten the clamp.
14.
Install the 3” band clamp onto
the outlet of the Left tailpipe and
install the left tailpipe tip onto the left
tailpipe. Install the driver-side tailpipe
tip hanger into the rear rubber hanger.
Keep the wrapping on until installation
is complete. The tip and the clamp
should be rotated so the clamp nut
and drain hole are pointing down.
repeat this process for the right side
tailpipe tip installation. See Figure 7.
15.
Be sure that the two (2) tailpipes
are completely engaged into the Y-pipe.
adjust your tailpipes so that the tips
are symmetrical and 1” below the rear
bumper. The hanger pins should be
parallel with the frame-mounted pin and
the rear rubber hangers are all slightly
positioned forward (See Figure 8).
NOTE: Recommended distance
between exhaust tip and body is
1
⁄
2
-inch to 1-inch.