Banks Power Chevy_GMC Trucks: Duramax LML (Diesel ’11 - 14 6.6L) Intake- Ram-Air Super Scoop '11-13 User Manual
Page 2
2
96556 v.2.0
Table of Contents
General Installation Practices ............. 2
Tools Required .................................... 2
Section 1; General Assembly .............. 3
Section 2; Super-Scoop Installation .... 4
Templates ........................................... 8
:
The Super-Scoop kit is designed
to work on vehicles with factory
sized wheels/tires. Running
oversized wheels/tires may cause
interference between the tire
and Super-Scoop. Also, please
be aware that fender lining and/
or bumper valance trimming is
required for this kit.
the manufacturer’s safety precautions.
Take care to balance the vehicle to
prevent it from slipping or falling. When
using ramps, be sure the front wheels
are centered squarely on the topsides;
put the transmission in park; set the
parking brake; and place blocks behind
the rear wheels.
: Do NoT uSe
fLooR jACkS To SuPPoRT The
vehiCLe whiLe woRkiNG uNDeR
iT. Do NoT RAiSe The vehiCLe
oNTo CoNCReTe BLoCkS,
MASoNRy oR ANy oTheR iTeM
NoT iNTeNDeD SPeCifiCALLy foR
ThiS uSe.
: This product is intend-
ed for general highway use. Do
not use this product when ford-
ing streams or crossing bodies of
water. Although this product is
designed to separate water from
entering the engine during normal
highway driving in rainy conditions,
it is not intended to be submerged
under water for any amount of
time. Regularly check the inlet of
the Super-Scoop for any obstruc-
tion or debris that may impede the
flow of air. After the installation of
the Super-Scoop be aware of the
decreased ride height and drive
accordingly to avoid damage to
the Super-Scoop. Regularly check
to make sure the Super- Scoop is
fastened securely and that all hard-
ware and fasteners are tight and in
good condition.
Definitions of ANSI Z535
Safety Standards
: Indicate[s] a hazard-
ous situation which, if not avoided, will
result in death or serious injury.
: Indicate[s] a hazard-
ous situation which, if not avoided, could
result in death or serious injury.
: Indicate[s] a hazard-
ous situation which, if not avoided, could
result in mild or moderate injury.
: Indicate[s] a situation that
requires your immediate attention.
Tools Required
✓
•
³/₈"
drive ratchets with
metric sockets ............................
• Standard and Phillips head
screwdrivers ...............................
• Standard and needle-nose
pliers
...........................................
• Clean shop towels or rags ..........
• Electric Drill .................................
• Drill Bits:
¹/₈",
³/₈", ¹/₄",
⁵
/₁₆"
.........
• Utility knife ...................................
• Permanent marker ......................
General Installation
Practices
1.
For ease of installation of your
Banks Ram-Air Super-Scoop, familiarize
yourself with the procedure by read-
ing the entire manual before starting
work. This manual contains 16 pages
of copy, illustrations and parts listing.
If any pages are missing from this man-
ual please call Gale Banks Engineering
immediately for a replacement.
2.
The exploded view of the Ram-Air
Super-Scoop assembly (page 3) pro-
vides only general guidance. Refer to
each step and section diagram in this
manual for proper instruction.
3.
Throughout this manual, the left
side of the vehicle refers to the driver’s
side, and the right-side to the passen-
ger’s side.
4.
Disconnect the ground cable from
the battery before beginning work. If
there are two batteries, disconnect
both.
5.
Route and tie wires and hoses
a minimum of 6 inches away from
exhaust heat, moving parts and sharp
edges. clearance of 8 inches or more is
recommended where possible.
6.
During installation, keep the work
area clean. If foreign debris is trans-
ferred to any Banks system compo-
nent, clean it thoroughly before install-
ing.
7.
When raising the vehicle, support it
on properly weight-rated safety stands,
ramps or a commercial hoist. Follow
Dear Customer,
If you have any questions con-
cerning the installation of your
Banks Ram-Air
®
Super-Scoop
®
,
please call our Technical Service
Hotline at (888) 839-2700
between 7:00 am and 4:00 pm
(PT). If you have any questions
relating to shipping or billing,
please contact our Customer
Service Department at (888) 839-
5600.
Thank you.