Xylem IM248R01 High Temp Sump Pump - Manual (Page 3)

3
0 10 20 30 40 50 60 70 80 GPM
0
0
10
10
0
20
30
m 3 /hr
5
10
40
METERS FEET
TOT
AL
D
YNAMIC HEAD
CAPACITY
MODEL: WEHT03xxM
SIZE: 2" Discharge
RPM: 1750
HP: .33 HP
SOLIDS: 3 / 4 " Diameter
15 5
5
15
25
35
WEHT03M 1 FT
2 GPM
Derate at
200ºF (93ºC)
68ºF (20ºC)
INTRODUCTION
Goulds Water Technology High Temperature 3885 Series
Effluent pumps are recommended for use in High Tem-
perature applications up to 200ºF. The High Tempera-
ture 3885 Pump handles ¾” solids . Common applica-
tions include boiler blow down and High Temperature
condensate. Pump should be operated with a High
Temperature float switch sold separately.
SAFETY INSTRUCTIONS
TO AVOID SERIOUS OR FATAL PERSONAL
INJURY OR MAJOR PROPERTY DAMAGE, READ
AND FOLLOW ALL SAFETY INSTRUCTIONS IN
MANUAL AND ON PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE PUMP.
This is a SAFETY ALERT SYMBOL.
When you see this symbol on the pump
or in the manual, look for one of the
following signal words and be alert
to the potential for personal injury or
property damage.
Warns of hazards that WILL cause
serious personal injury, death or major
property damage.
Warns of hazards that CAN cause
serious personal injury, death or major
property damage.
Warns of hazards that CAN cause per-
sonal injury or property damage.
NOTICE: INDICATES SPECIAL INSTRUCTIONS
WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.
THOROUGHLY REVIEW ALL INSTRUCTIONS
AND WARNINGS PRIOR TO PERFORMING ANY
WORK ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
All electrical work must be performed
by a qualified technician. Always follow
the National Electrical Code (NEC), or the Canadian
Electrical Code, as well as all local, state and provincial
codes. Code questions should be directed to your local
electrical inspector. Failure to follow electrical codes and
OSHA safety standards may result in personal injury or
equipment damage. Failure to follow manufacturer’s
installation instructions may result in electrical shock, fire
hazard, personal injury or death, damaged equipment,
provide unsatisfactory performance, and may void manu-
facturer’s warranty.
DANGER
WARNING
CAUTION
Standard units are not designed for use in
swimming pools, open bodies of water,
hazardous liquids, or where flammable gases exist. These
fluids and gases may be present in containment areas.
Tank or wetwell must be vented per local codes.
Only pumps specifically Listed for Class 1, Division 1
are allowable in hazardous liquids and where flammable
gases may exist. See specific pump catalog bulletins or
pump nameplate for all agency Listings.
Disconnect and lockout electrical power
before installing or servicing any electrical
equipment. Many pumps are equipped with automatic
thermal overload protection which may allow an over-
heated pump to restart unexpectedly.
Do not use pump flammalde or explo-
sive liquids. Pump is for water only.
PERFORMANCE
PRE-INSTALLATION CHECKS
Open all cartons and inspect for shipping damage.
Report any damage to your supplier or shipping carrier
immediately.
Important: Always verify that the pump nameplate
Amps, Voltage, Phase and HP ratings match your control
panel and power supply.
This pump is oil-filled. If there are any signs of oil leak-
age or if the unit has been stored for an extended period
check the oil level in the motor dome and the seal hous-
ing, if so equipped.
Check the motor cover oil level through the pipe plug on
top of the unit. The motor chamber oil should just cover
the motor. Do not overfill, leave room for expansion!
WARNING
WARNING
WARNING
WARNING
MODELS
Order
Number
HP Phase Volts RPM Impeller
Dia. (In.)
Max.
Amps LRA
KVA
Code
Full Load
Motor Eff.
Resistance Wt.
(Lbs.)
Cord
Length Start Line-Line
WEHT0311M
0.33 1
115
1750 5.38
12.0 31.1 J 55 9.3 1.4
56 20' WEHT0318M 208 7.3 19.5 K 51 9.1 4.2
WEHT0312M 230 6.1 16.5 J 54 11.7 5.6
*Add P1 to the end of the order number to include an ultra hi-temp float switch in the purchase.
Replacement part numbers for float: A2HT31 – 115V and A2HT32 – 208 and 230V (20' cord length).