NXG Technology NX-522DVC - Manual (Page 2)

FIG. 4
(Continued from front)
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials within three
years from the date of the original customer’s purchase, we will, at our option, repair or
replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a particular
purpose, are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the product
at our option. NXG shall not be liable for incidental or consequential damages of any kind
or character because of product defects. Some states do not allow limitations on how
long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations and exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with
the carrier.)
Warranty Service
Warranty service must be performed by an authorized service center, usually a NXG speaker
systems dealer or its authorized agent. You may obtain a list of authorized service centers by
contacting NXG. All warranty repairs must be accompanied by the original bill of sales. No
other document is acceptable or is required. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
NXG reserves the right to revise speaker system specifications without notice.
6. See Fig. 5. With the speaker wire attached to the
speaker, slide the speaker up inside the cut-out hole.
Center the speaker in the cut-out hole and turn the
four locking screws counterclockwise until the speak-
er is drawn up snugly to the wall board from behind,
clamping the speaker in place. Try to tighten each
screw equally. Replace the speaker grill by gently
pressing it into place.
New Construction
1. Determine speaker location and mark it on
your plans for future reference.
2. If possible, run speaker wires after HVAC and
electrical wiring is in place.
3. Secure speaker wires in place along the run with
insulated staples only and be careful not to pierce the
wire’s insulation. Allow a bit of slack for expansion
of building materials.
4. Needless to say, the actual speaker should not
be installed until the wall board is in place. In the
meantime, leave several feet of wire coiled up and
secured at the back side of the mounting hole.
5. To complete the installation follow steps 2
through 5 above.
Operational Check
After making all connections it’s a good idea to make
sure every thing is working properly. Turn on your
stereo system making sure the volume control is
turned down and that the balance control is in the
center position. Activate a musical source such as
FM, a CD or DVD player. Gently turn up the volume.
You should hear music coming from your new NXG
speaker. If no sound is heard from the speaker,
switch off the system immediately and check for
open or loose connections, wrong polarity or shorts.
FIG. 5
NX-522DVC Specifications
Maximum Power Handling: 60 watts
Sensitivity: 90dB @ 1 watt/1 meter
Frequency Response: 65 Hz-21,000 Hz
Driver Complement: 5 1 /
4
˝ (133 mm) dual voice coil aluminum anodized cone
woofer w/rubber surround
3 /
4
˝ (19 mm) pivoting liquid-cooled titanium dome tweeter
Nominal Impedance: 8 ohms
Overall Dimensions: 7 15 /
16
˝ (diameter) round x 3˝ D
Required Ceiling Cut-out: 6 1 /
2
˝ (diameter) round
16648 North 94th Street
Scottsdale, AZ 85260
1-800-733-0008