NXG Technology NX-PRO1030 - Manual (Page 2)

(Continued from front)
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials within three
years from the date of the original customer’s purchase, we will, at our option, repair or
replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a particular
purpose, are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the product at
our option. NXG shall not be liable for incidental or consequential damages of any kind or
character because of product defects. Some states do not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitations and exclusions may not apply.
5. Attach the wire to the input terminals on the
rear of the speaker. Remember to maintain proper
polarity with the amplifier by attaching the positive
(+) lead to the red terminal and the negative (-)
lead to the black terminal.
6. See Fig. 5. With the speaker wire attached to
the speaker, slide the speaker up inside the cut-out
hole. Center the speaker in the cut-out hole and
turn the four locking screws clockwise until the
speaker is drawn up snugly to the wall board
from behind, clamping the speaker in place. Try to
tighten each screw equally. Replace the speaker
grill by gently pressing it into place.
New Construction
1. Determine speaker locations and mark them on
your plans for future reference.
2. If possible, run speaker wires after HVAC and
electrical wiring is in place.
3. Secure speaker wires in place along the run
with insulated staples only and be careful not to
pierce the wire’s insulation. Allow a bit of slack
for expansion of building materials.
4. Needless to say, the actual speakers should not
be installed until the wall board is in place. In the
meantime, leave several feet of wire coiled up and
secured at the back side of the mounting hole.
5. To complete the installation follow steps 2
through 5 above.
FIG. 5
16648 North 94th Street • Scottsdale, AZ 85260
1-800-733-0008
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)
FIG. 4
Warranty Service
Warranty service must be performed by an authorized service center, usually an NXG speaker
systems dealer or its authorized agent. You may obtain a list of authorized service centers by
contacting NXG. All warranty repairs must be accompanied by the original bill of sales. No
other document is acceptable or is required. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
NXG reserves the right to revise speaker system specifications without notice.
Specifications
Maximum Power Handling: 5 - 150 watts
Sensitivity: 90dB @ 1 watt/1 meter
Frequency Response: 28 Hz-22,000 Hz
Driver Complement:
• 10˝ (254 mm) metallic anodized injection-molded radiative cone woofer w/ rubber surround
• 3 3 /
4
˝ (95 mm) metallic anodized injection-molded cone midrange w/ rubber surround
• 1˝ (25 mm) liquid-cooled tweeter with metallic anodized dome diaphragm
Nominal Impedance: 8 ohms
Grille: Corrosion-resistant powder coated aluminum
Overall Dimensions: 13˝ (diameter) round x 5 1 /
2
˝ D
Required Ceiling Cutout: 11 3 /
4
˝ (diameter) round
Operational Check
After making all connections it’s a good idea to
make sure every thing is working properly. Turn on
your surround or stereo system making sure the
volume control is turned down and that the balance
control is in the center position. Activate a musical
or movie source such as FM, a CD or DVD player.
Gently turn up the volume, you should hear sound
coming from your new NXG speakers. If no sound
is heard from any or all speakers, switch off the
system immediately and check for open or loose
connections, wrong polarity or shorts, or proper
source selection.