NXG Technology NX-PRO5520CLR - Manual (Page 2)

FIG. 5
(Continued from front)
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship
or materials within three years from the date of the original cus-
tomer’s purchase, we will, at our option, repair or replace the
defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability
and fitness for a particular purpose, are limited in duration to the
length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or
replacement of the product at our option. NXG shall not be liable
for incidental or consequential damages of any kind or character
because of product defects. Some states do not allow limitations
on how long an implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or consequential damages,
so the above limitations and exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or
improper operation.
• Any product whose serial number has been altered, defaced,
or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage
must be made with the carrier.)
Warranty Service
Warranty service must be performed by an authorized service
center, usually an NXG speaker systems dealer or its authorized
agent. You may obtain a list of authorized service centers by con-
tacting NXG. All warranty repairs must be accompanied by the
original bill of sales. No other document is acceptable or is
required. This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
NXG reserves the right to revise speaker system specifications without notice.
New Construction
1. Determine speaker locations and mark them on your plans for future reference.
2. If possible, run speaker wires after HVAC and electrical wiring is in place.
3. Secure speaker wires in place along the run with insulated staples only and
be careful not to pierce the wire’s insulation. Allow a bit of slack for expan-
sion of building materials.
4. The actual speakers should not be installed until the wall board is in place.
In the meantime, leave several feet of wire coiled up and secured at the back
side of the mounting hole.
5. To complete the installation follow steps 2 through 5 above.
FIG. 4
6. See Fig. 5. With the speaker wire attached to the speaker, slide the
speaker up inside the cut-out hole. Center the speaker in the cut-out hole and
turn the six locking screws counterclockwise until the speaker is drawn up
snugly to the wall board from behind, clamping the speaker in place. Try to tight-
en each screw equally. Replace the speaker grill by gently pressing it into place.
Specifications
Tweeter: Pivoting liquid-cooled 1˝ (25mm)
tweeter w/ metallic anodized dome diaphragm
Woofers: Two 5 1 /
4
˝ (133mm) metallic anodized
injection-molded radiative cone technology
woofers with rubber surrounds
Crossover: 12 dB Electro Acoustic crossover
w/ gold-plated input terminals
Frequency Response: 45 Hz-22,000 Hz
Impedance: 8 ohms nominal
Power Handling: 5 -120 watts
Sensitivity: 89dB @ 1 watt/1 meter
Grille: Fine mesh aluminum grille
Overall Dimensions: 7 3 /
8
˝ H x 15 3 /
16
˝ W x 3 1 /
2
˝ D
Cutout Dimensions: 6 3 /
8
˝ x 13 3 /
4
˝
Operational Check
After making all connections it’s a good idea to make sure everything is working
properly. Turn on your stereo system making sure the volume control is turned
down and that the balance control is in the center position. Activate a musical
source such as FM, a CD or DVD player. Gently turn up the volume. You should
hear music coming from your new NXG speakers. If no sound is heard from
any or all speakers, switch off the system immediately and check for open or
loose connections, wrong polarity or shorts.
16648 North 94th Street
Scottsdale, AZ 85260
1-800-733-0008