NXG Technology NX-PRO6500S - Manual (Page 2)

NXG Speaker Systems are designed to the highest possible value and performance
standards. Our confidence in their quality is such that NXG Technology offers cus-
tomers this transferable limited warranty:
NXG Speaker System Two-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials within
two years from the date of the original customer’s purchase, we will, at our option,
repair or replace the defective product.
DISCLAIMER
THE WARRANTY STATED HEREIN IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR PARTICULAR
PURPOSE AND ALL OTHER LIABILITIES AND OBLIGATIONS OF NXG TECHNOLOGY, ALL
OF WHICH ARE EXPRESSLY DISCLAIMED. NXG TECHNOLOGY HAS NOT MADE AND
DOES NOT HEREBY MAKE ANY OTHER REPRESENTATION, WARRANTY OR COVENANT
WITH RESPECT TO THE CONDITION, QUALITY, DURABILITY, DESIGN, OPERATION,
CAPACITY, FITNESS FOR USE OR SUITABILITY OF THE NXG SPEAKER SYSTEMS.
Exclusion of Certain Damages
NXG Technology’s liability for any defective product is limited to repair or replacement
of product at our option. NXG Technology shall not be liable for incidental
or consequential damages of any kind or character because of product defects.
Some states do not allow limitations on how long an implied warranty lasts and/or
do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations and exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or
improper operation.
• Any product whose serial number has been altered, defaced,
or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage
must be made with the carrier.)
Warranty Service
Warranty service must be performed by an authorized service center,
usually an NXG speaker systems dealer or its authorized agent. All
warranty repairs must be accompanied by the original bill of sales. No
other document is acceptable or is required. This warranty gives you
specific legal rights, and you may also have other rights which vary
from state to state.
NXG reserves the right to revise speaker system specifications without notice.
16648 North 94th Street • Scottsdale, AZ 85260
1-800-733-0008 www.nxgtech.com
(See Fig. 4 for speaker connection detail)
• Strip the outer jacket from each end of the cable about 3 inches and expose the two
insulated conductors.
• Strip
1 /
2
˝ of insulation from the end of each conductor.
• Twist the positive wire to the Red wire and the negative wire to the Black wire of the
NX-PRO6500 speaker.
• Make sure the two connections do not touch each other for the next step
• Connect the positive and negative wires to your receiver/amplifier maintaining proper polarity
as described in your receiver/amplifier’s manual.
• Now turn your receiver/amplifier on, making sure the volume control is turned down and that the
balance control is in the center position. Activate a musical source such as FM or a CD player.
Gently turn up the volume until you hear sound coming from your new NX-PRO6500 rock speakers.
If everything is working properly, then turn the amplifier off and skip down to the next paragraph. If
no sound is heard from any or all speakers, switch off the receiver/amplifier immediately and check
for open or loose connections, wrong polarity or shorts, or improper source selection.
• Place wire nuts on each of the speaker connections and fill them with silicone (not supplied)
to prevent corrosion after the wire is buried. Use silicone to seal the cable path through any
walls or other structures. You can now fill in the cable trench with the dirt you removed, and
start to enjoy your new outdoor sound system.
FIG. 3
Typical System with
local volume control Receiver
Rock
Speaker
3/4˝ PVC Conduit
NX-VM80 Volume
Control in NX-OVC
Outdoor Enclosure
House
Rock
Speaker
Specifications
Power Handling: 10 – 100 Watts
Efficiency: 89dB @ 1watt/1 meter
Frequency Response: 60 Hz – 20,000 Hz
Driver Complement:
6
1 /
2
˝ (165mm) injection-molded cone woofer
3 /
4
˝ (19mm) polycarbonate dome tweeter
Nominal Impedance: 8 ohms
Connection: 24˝ Two-Conductor Pig Tail
Enclosure: Silicone sealed, glass-reinforced,
cast resin
Grille: Color matched aluminum
Overall Dimensions: 14˝ (356mm) W x
10 1 /
2
˝ (267mm) H x 9 3 /
4
˝ (248mm) D
Available Colors: Granite & Sandstone
FIG. 4 - Speaker Connection
(Continued from front)
Note: Once wires
have been twisted
together and wire
nuts screwed on,
fill inside of wire nut
and cover exposed
bare wire with
silicone sealant.
Install wire nuts
on twisted wires Twist wires
together
as shown
(+) Red
(–) Black
To Rock
Speaker
From
Receiver
Note: Aim front (grille)
of rock speaker toward
listening area.