NXG Technology NX-C8.3-P - Manual (Page 2)

(Continued from front)
6. See Fig. 6. With the speaker wire attached to the speaker, slide
the speaker up inside the cut-out hole. Center the speaker in the
cut-out hole and turn the four locking screws clockwise until the
speaker is drawn up snugly to the wall board from behind, clamping
the speaker in place. Try to tighten each screw equally. Replace the
speaker grill by gently pressing it into place.
New Construction (A)
Note: Use of optional new construction rough-in bracket kits will
not only save time but will also enhance the sound quality of your
installed speakers. (See rough-in kit installation manual for mounting
instructions when using kits.)
New Construction (B)
(Installation without use of new construction rough-in brackets.)
1. Determine speaker locations and mark them on your plans for
future reference.
2. If possible, run speaker wires after HVAC and electrical wiring is
in place.
3. Secure speaker wires in place along the run with insulated staples
only and be careful not to pierce the wire’s insulation. Allow a bit of
slack for expansion of building materials.
4. Needless to say, the actual speakers should not be installed until
the wall board is in place. In the meantime, leave several feet of wire
coiled up and secured at the back side of the mounting hole.
5. To complete the installation follow steps 2 through 5 above.
FIG. 6
16648 North 94th Street • Scottsdale, AZ 85260
1-800-733-0008 www.nxgtech.com
NXG Pro Series Three -Year Limited Warranty
If the NXG Pro Series speaker system proves to be defective in workmanship or materials within
three years from the date of the original customer’s purchase, we will, at our option, repair or
replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a particular purpose,
are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the product at our
our option. NXG shall not be liable for incidental or consequential damages of any kind or character
because of product defects. Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with
the carrier.)
Warranty Service
Warranty service must be performed by an authorized service center, usually an NXG speaker
systems dealer or its authorized agent. You may obtain a list of authorized service centers by con-
tacting NXG. All warranty repairs must be accompanied by the original bill of sales. No other doc-
ument is acceptable or is required. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. NXG reserves the right to revise speaker system
specifications without notice.
Operational Check
After making all connections, it’s a good idea to make sure every-
thing is working properly. Turn on your surround or stereo system,
making sure the volume control is turned down and that the balance
control is in the center position. Activate a musical or movie source
such as FM, a CD or DVD player. Gently turn up the volume, you
should hear sound coming from your new NXG speakers. If no
sound is heard from any or all speakers, switch off the system
immediately and check for open or loose connections, wrong polar-
ity or shorts, or proper source selection.
NX-C8.3-P Specifications
Maximum Power Handling: 5 - 150 watts
Sensitivity: 90dB @ 1 watt/1 meter
Frequency Response: 35 Hz-22,000 Hz
Driver Complement:
8˝ (204mm) metallic-anodized, graphite-filled, injection-molded RCT
cone woofer with rubber surround
2 1 /
2
˝ (63mm) metallic-anodized, polycarbonate cone midrange
1˝ (25mm) minimum diffraction, pivoting, fluid-cooled, high tenacity
teteron dome tweeter
Impedance: 8 ohms nominal, 6 ohms minimum
Grille: Corrosion-resistant powder coated aluminum
Overall Dimensions (Diameter x Depth): 10 3 /
4
˝ x 4˝ D (273 mm x 102 mm)
Required Ceiling Cutout: 9 1 /
2
˝ (241 mm) diameter
FIG. 5