Atec Chroma-62015B Series - Manual (Page 5)

SPECIFICATIONS
Model 62015B-15-90 62015B-30-50 62015B-60-25 62015B-80-18 62015B-150-10
Electrical Specifications
Output Ratings
Output Power 1350W 1500W 1500W 1440W 1500W
Output Voltage 1~15V 1~30V 1~60V 1~80V 1~150V
Output Current 1~90A 1~50A 1~25A 1~18A 1~10A
Line Regulation 0.1% FS
Load Regulation *1 1% FS
Programming Accuracy 1% FS
Measurement Accuracy 1% FS
Output Noise (20MHz)
Voltage Noise (P-P) 100mV 100mV 200mV 200mV 400mV
Voltage Ripple (rms) 30mV 30mV 50mV 50mV 100mV
Current Ripple (rms) 0.9A 0.5A 0.25A 0.18A 0.1A
Efficiency > 87% @ full load > 88% @ full load
Turn on over shoot voltage *2 5% of nominal output
Transient Response Time *3 < 5 ms
AC Input Voltage
Six Position Mainframe
187 ~ 250 Vac (3 Phase 4 Wire,
Δ
Connection ) or 323 ~ 437 Vac (3 Phase 5 Wire, Y Connection) /
45 ~ 65 Hz
Three Position Mainframe 187 to 250 Vac (single phase) / 45 ~ 65 Hz
Input Power Factor > 0.98@ full load
Protection Function
OVP Automatically shuts down at 115% of set value
Adjustment Range 1~16V 1~31V 1~65V 1~83V 1~155V
OCP Current limit (0 ~ 100%) / OCP Shutdown at 115% of F.S.
OTP Automatically shuts down if internal limit is reached
I/O Signal
Remote ON/OFF (I/P) Dry contact (closed = enabled), vice versa
AUX Voltage 4 ~ 24V / 0.5A at mainframe (by trimmer adjust voltage)
DC OK Signal Type (O/P) Dry contact (closed = enabled) (Error : OVP / OCP / OTP / AC Fault)
Programming Response Time *4 (Typical)
Rise Time (Full Load) For a programmed 5% to 95% step in output voltage : 100ms
Rise Time (No Load) For a programmed 5% to 95% step in output voltage : 100ms
Fall Time (Full Load) For a programmed 95% to 5% step in output voltage : 40ms
Fall Time (No Load) For a programmed 95% to 5% step in output voltage : 5s
Vout Setting CAN Bus send command to DC module receiver : 1s
Measurement V & I Under CAN command using fetch : 100ms
Delay Time For output ON/OFF enable and disable (under CAN command) : 5s(Single Mainframe)
General Specifications
Remote Sensing
3V max. line loss compensation
Parallel Operation Current Sharing (
±
5%)
Operating Temperature 0 ~ 50
℃
Humidity Range 0 ~ 90% RH. Non-condensing
Remote Interface CAN Bus (optional)
Safety & EMC CE
Dimension (H x W x D)
Mainframe : 175.6 x 443.9 x 466.2 mm / 6.91 x 17.48 x 18.35 inch (62000B-6-1)
Mainframe : 175.6 x 239.9 x 466.2 mm / 6.91 x 9.44 x 18.35 inch (62000B-3-1)
Module : 138.5 x 67.5 x 377.5 mm / 5.45 x 2.66 x 14.86 inch
Weight
Mainframe : 14 Kg / 30.8 lbs (62000B-6-1)
Mainframe : 8 Kg / 17.6 lbs (62000B-3-1)
Module : 4 Kg / 8.8 lbs
All specifications are subject to change without notice. Please visit our website for the most up to date specifications.
Note*1 : For 50% step load variation with remote sense at maximum output voltage
Note*2 : based on rise time of 100ms
Note*3 : Time for the output voltage to recover within 1% of its rated for a load changed of 25%
Note*4 : Six Position Mainframe through CAN