Document Outline

• 2 Eclipse-Omega PSUs
  • 2.1 Preparation before Upgrading the Eclipse-Omega for Fibre Interfaces
    • 2.1.1 Important Information
  • Omega Fibre Trunk Preparation
    • 2.2.1 Required Equipment
    • 2.2.2 Upgrade Steps
• Eclipse-Omega & Eclipse-Median Configuration/CPU Card
  • 3.1 Important Information
  • Updating the Omega & Median Configuration card Boot ROM
    • Required Equipment
  • 3.3 Updating the Configuration Card Application
  • 3.4 Eclipse Configuration Card Application using ECS (serial)
    • 3.4.1 Connecting via Serial
    • 3.4.2 Required Equipment
    • 3.4.3 Upgrade Steps
    • 3.4.4 Sending the new update file
  • 3.5 Eclipse Configuration Card Application using ECS (Ethernet)
    • 3.5.1 Required Equipment
    • Upgrade Steps
      • 3.5.2.1 Opening the Linked set or Layout information
  • 3.6 Updating the Eclipse Configuration Card Application using S4 Driver
    • 3.6.1 Required Equipment
    • 3.6.2 Upgrade Steps
  • Updating the Eclipse Configuration Card using TeraTerm
    • 3.7.1 Required Equipment
    • 3.7.2 Upgrade Steps
  • Updating the Configuration Card’s Xilinx ICs
    • 3.8.1 Required Equipment
• 4 Eclipse-PiCo & E32
  • 4.1 Important Information
  • 4.2 Eclipse-PiCo / E32 Boot ROM
    • Required Equipment
    • Upgrade Steps
  • 4.3 Updating the Eclipse-PiCo / E32 Application
  • 4.4 Eclipse-PiCo / E32 Configuration Card Application using ECS (serial)
    • 4.4.1 Required Equipment
    • 4.4.2 Upgrade Steps
      • 4.4.2.1 Opening the Linked set or Layout information
      • 4.4.2.2 Sending the new update file
  • 4.5 Eclipse-PiCo / E32 Configuration Card Application using ECS (Ethernet)
    • 4.5.1 Required Equipment
    • 4.5.2 Upgrade Steps
      • 4.5.2.1 Opening the Linked set or Layout information
  • 4.6 Eclipse-PiCo / E32 Configuration Card Application using S4 Driver
    • 4.6.1 Required Equipment
    • 4.6.2 Upgrade Steps
  • 4.7 Eclipse-PiCo / E-32 Configuration Card Application using TeraTerm
    • 4.7.1 Required Equipment
    • 4.7.2 Upgrade Steps
  • Eclipse-PiCo / E32 Xilinx
    • Required Equipment
• Omega & Median MVX-A16 updates
  • 5.1 Important Information
  • 5.2 Eclipse MVX-A16 Card H8 Application Upgrade
    • Required Equipment
    • 5.2.2 Upgrade Steps
  • 5.4 Eclipse MVX-A16 Card Xilinx FPGA Upgrade
    • 5.4.1 Required Equipment
  • MVX-A16 Firmware Version Checking
    • 5.5.1 Using the Matrix Event Log in ECS
    • 5.5.2 Using TeraTerm
• 6 Eclipse-PiCo & E32 MVX
  • 6.1 Important Information
  • 6.2 Eclipse-PiCo / E32 MVX Card H8 Application Upgrade
    • Required Equipment
    • 6.2.2 Upgrade Steps
  • 6.3 Eclipse-PiCo / E32 Xilinx
    • Required Equipment
  • Eclipse-PiCo/E-32 MVX Firmware Version Checking
    • 6.4.1 Using the Matrix Event Log in ECS
• 7 E-FIB Eclipse-Omega and Median Fibre Trunking Cards
  • 7.1 Important Information
  • 7.2 E-Fib Xilinx Flash Programming
• 8 Omega/Median E-QUE Cards
  • 8.1 E-QUE Application Upgrade
    • 8.1.1 Required Equipment
    • 8.1.2 Using TeraTerm to upgrade the E-Que card
  • 8.2 FPGA Xilinx Upgrade
  • Programming
• 9 Eclipse Configuration System
  • 9.1 Important Information
  • 9.2 Overwrite of Existing ECS Installation
    • Required Equipment
    • 9.2.2 Upgrade Steps
  • Clean Installation of ECS
    • 9.3.1 Required Equipment
    • 9.3.2 Upgrade Steps
    • 9.3.3 Uninstalling ECS versions 2.2 or EARLIER VERSIONS
    • Uninstalling ECS versions 4.0 or LATER VERSIONS
• 10 Wireless System
  • 10.1 Beltpacks
  • 10.2 Active Antenna
  • 10.3 Splitter
• 11 Panels
  • 11.1 General Upgrading Panels via ECS
    • 11.1.1 Important Information
    • 11.1.2 Required Equipment
    • 11.1.3 Upgrade Steps
      • For PD4215E, PD4226E, PD4224E, PD4294E panels
    • 11.1.4 Notes - V-Series
    • 11.1.5 Notes - ICS-52/92
  • 1.1 I
    • 11.2.1 Important Information
      • 11.2.1.1 Required Equipment
      • 11.2.1.2 Upgrade Steps
  • 11.3 4000 Series II Panels
    • 11.3.1 Important Information
    • 11.3.2 PD4212E Panel
      • Required Equipment
      • 11.3.2.2 Upgrade Steps
    • 11.3.3 PD4222E Panel
      • Required Equipment
      • 11.3.3.2 Upgrade Steps
    • PD4215E Panel
      • Required Equipment
      • 11.3.4.2 Upgrade Steps
    • 11.3.5 PD4224E Panel
      • Required Equipment
      • 11.3.5.2 Upgrade Steps
    • PD4294E Panel
      • Required Equipment
      • 11.3.6.2 Upgrade Steps
  • 11.4 I-Station Series
    • 11.4.1 Important Information
    • I-Station
      • Required Equipment
      • 11.4.2.2 Upgrade Steps
    • 11.4.3 E-Station
      • Required Equipment
      • 11.4.3.2 Upgrade Steps
  • V-Series
    • 11.5.1 Important Information
    • 11.5.2 Overview
    • 11.5.3 Notes
  • 11.6 Expansion Panels
  • 11.7 V-Series – Upgrade via direct Ethernet connection
    • Software and PC Setup
    • 11.7.2 Updating the U-Boot Loader
    • 11.7.3 Updating the Kernel, Kernel Root Filesystem and Application Files
• TEL-14
  • Introduction
  • 12.2 Upgrading the Hardware
    • 12.2.1 Requirements
    • 12.2.2 Procedure
  • 12.3 Updating the Firmware
    • 12.3.1 Requirements
    • 12.3.2 Procedure
• 13 AES-6
  • 13.1 AES-6 Application Upgrade
    • 13.1.1 Important Information
    • 13.1.2 Required Equipment
    • 13.1.3 Procedure
  • 13.2 AES-6 FPGA Upgrade
    • 13.2.1 Overview
    • 13.2.2 Required Equipment
    • 13.2.3 Procedure
    • 13.2.4 Procedure : FPGA image present
    • 13.2.5 Procedure : FPGA image NOT present
• 14 Appendices
  • 14.1 Appendix A – Configuration Card Layout
  • 14.2 Appendix B – Eclipse-Omega / Median Configuration Card DIP Switches
  • 14.3 Appendix C – Eclipse-Pico/E-32 Configuration Card Layout
  • 14.4 Appendix D – Eclipse-Pico/E-32 Configuration Card DIP Switch Settings
  • 14.5 Appendix E – Eclipse-Omega / Median MVX-A16 Card Layout
  • 14.6 Appendix F – Eclipse-Omega / Median MVX-A16 Interface Cable
  • 14.7 Appendix G – Eclipse-Pico/E-32 PCB Layout
  • 1.1 A
  • 14.9 Appendix J – TFTPUtil Installation
  • 14.10 Appendix K – TeraTerm Installation
  • 14.11 Appendix L – S4 Driver Installation
  • 14.12 Appendix M – Flash Magic Installation
  • 14.13 Appendix N– I-Station Converter Cable and Rear Panel Layouts