Clear-Com HX System Frames User Manual
Eclipse hx configuration software (ehx), User guide
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- Document Reference
- Contents
- 1 Introduction to EHX
- 2 Getting started: installing, starting and exiting EHX
- 3 EHX: setting up a system
- 3.1 Introduction
- 3.2 Matrix ethernet operation
- 3.3 Selecting ethernet or serial connection
- 3.4 Creating a project file
- 3.5 Setting up a new matrix
- 3.5.1 Adding an offline matrix
- 3.5.2 Adding a discovered matrix
- 3.5.3 Matrix preferences menu
- 3.5.4 Configuration options
- 3.5.5 Firmware options
- 3.5.6 Delete matrix from project
- 3.5.7 Apply changes to matrix
- 4 Managing configurations and users
- 4.1 Introduction
- 4.1.1 Creating a new project
- 4.1.2 Opening a project
- 4.1.3 Closing a project
- 4.1.4 Importing and exporting a project
- 4.1.5 Saving a project
- 4.1.6 Deleting a project
- 4.1.7 Importing/exporting configuration keysets
- 4.1.8 User management
- 4.1.9 Creating a new EHX user
- 4.1.10 Editing an existing EHX user
- 4.1.11 Deleting a user
- 4.2 The EHX screen after a project has been loaded
- 4.1 Introduction
- 5 Configuring the Eclipse HX system
- 5.1 Using the left pane EHX menus
- 5.2 Matrix hardware
- 5.3 Fonts
- 5.4 System configuration limits
- 5.5 Online
- 5.6 Matrix hardware setup
- 5.7 Adding an MVX-A16 card
- 5.8 Removing an MVX-A16 card
- 5.9 Upgrading the MVX-A16 cards
- 5.10 Port list options
- 5.11 Show all ports
- 5.12 Detect new hardware
- 5.13 Show Alt Text
- 5.14 Port number
- 5.15 Port function
- 5.16 Summary of expansion panels
- 5.17 Label
- 5.18 Description
- 5.19 Sorting ports
- 5.20 Column/row resizing
- 5.21 Port properties
- 5.21.1 Assignment panel (AP) panel options
- 5.21.2 Auxiliary relay options
- 5.21.3 Basic options
- 5.21.4 Panel options
- Reply tally auto clear time
- Display brightness
- Display dim timer
- Eavesdropping (privacy)
- Expansion panels
- Headset mic type
- Headset PTT function
- Headset LS cut
- Listen again auto delete
- Mute relay
- Nearby panel partial
- Page override allowed
- Page gain
- Gooseneck mic type
- Panel text orientation
- Line release
- Screen saver timer
- Applies to:
- 5.21.5 IP port options
- 5.21.6 Assignment panel options
- 5.21.7 Menu options
- 5.21.8 Voice operated switch
- 5.21.9 Global options
- 5.21.10 Gain options
- 5.21.11 Audible alert options
- 5.21.12 Tally options
- 5.21.13 Fast key assign options
- 5.21.14 Logic input options
- 5.21.15 Attached control options
- 5.21.16 DTMF options
- 5.22 General Purpose Inputs (GPIs)
- 5.23 General Purpose Outputs (GPOs)
- 5.24 Configuring the E-FIB fiber card
- 5.25 Configuring the E-Que card
- 5.26 E1 direct
- 5.27 T1 direct
- 5.28 E1 trunk
- 5.29 T1 trunk
- 5.30 E1 direct/trunk
- 5.31 T1 direct/trunk
- 5.32 E-QUE antenna
- 5.33 E-QUE splitter
- 5.34 Removing an E-Que card
- 5.35 Configuring an E-Que card for antenna
- 5.36 Splitter connections
- 5.37 Antenna role map
- 5.38 E-Que trunk basic settings
- 5.39 Configuring the IVC-32 card
- 5.40 Adding an IVC-32 card
- 5.41 Configuring an IVC-32 redundant card
- 5.42 Configuring the LMC-64 card
- 5.43 Configuring the E-MADI64 card
- 5.44 Fixed groups
- 5.45 Fixed group tallies
- 5.46 Sort groups
- 5.47 Key groups
- 5.48 Partylines
- 5.49 Routes
- 5.50 Speed dials
- 5.51 Controls
- 5.52 Logic Maestro
- 5.53 Beltpacks
- 6 IP devices
- 7 Panel programming
- 7.1 The panel programming screen
- 7.2 V-series panel programming
- 7.3 Concert panel programming
- 7.4 Concert panel options
- 7.5 I-Series programming
- 7.6 I-Series panel options
- 7.7 Fast key assign restrictions (I-series)
- 7.8 Setting up assignment panel partyline membership options
- 7.9 Setting up assignment panel fixed group membership options
- 7.10 General panel setups
- 7.11 Local advanced
- 8 Audio Mixer
- 9 Online mode
- 10 Networking
- 11 Client server
- 12 Eclipse HX downloads
- 13 Using the diagnostic tools
- 14 Glossary
- 15 Limited Warranty
- 16 Technical Support & Repair Policy