Controlled Products Systems Group LA400-S - Manual (Page 21)

21
Z22
R91
CLOSE
EDGE
R94
R92
R93
L1
R1
R2
Z1
K5
Ø14GPØ89ШE
Ш14LGШ89ШE
Ш14SKШ89ШE K6
K2
F3
10A 32V
D1Ø
OPEN EDGE/
PHOTO
OPEN
PHOTO
CLOSE
PHOTO
J18
R227
R2Ø7
Z2Ø
R223
P1
Z9
Z8
F2
F6
D4
D2
R9
C64
JMPR1
R224
U4
P2
J1
J19
SINGLE
BUTTON
CONTROL
INPUTS
FORCE
BIPART
DELAY
TIMER TO
CLOSE
MIN MAX OFF MAX OFF MAX
OPEN
SINGLE BUTTON
RESET
STOP
SHADOW
S1
INTERRUPT
CHGR
OVLD
COM
COM
COM
FUSE
OPEN
LOOP
INPUTS
POWER
BATT 1 BATT 2
F1 20A 32V
R35
D9
Z3
Z4
U3
D1
D27
F5
C11
C13
C12
D15
C2 R4
R1Ø1
R1ØØ
R9Ø
Q9 K1
R196
Q22
D8
K3
K4
D21
D22 C4
ACCESSORY
OVLD
D6
JMPR2
MOV1 MOV2
DB1
U2
Z12
24 VAC/
SOLAR
INPUT
GATE 2
ACCESSORY
POWER
MAGLOCK
ALARM
GATE 1
C
C
NC
NO
NO
GRN
WHT
YEL
BLU
RED
BRN
GRN
WHT
YEL
BLU
RED
BRN
F4
10A 32V
F7
24V
24V
COM
OVLD
OVLD
SWITCHED
ACCESSORY
POWER
TIMER
RUNNING GATE 2
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
LEARN
LIMITS
DIAGNOSTIC
GATE 1
J4
SAVE
MAGLOCK
MODE
EDGE
PHOTO OFF
OFF
SINGLE
NO
NO
ON
ON
DUAL
NC
NC
LEARN
XMITTER
S8 1 2 3 4 5 O N
2
1
MIN MAX OFF MAX OFF MAX
FORCE
GATE 2
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
LEARN
LIMITS
DIAGNOSTIC
GATE 1
TIMER TO CLOSE ENABLE
Set the TIMER TO CLOSE to
desired setting. The range is 0 to
180 seconds, 0 seconds is OFF.
FORCE CONTROL
Set the force control such that the unit will
complete a full cycle of gate travel but will
reverse off an obstruction without applying
an unreasonable amount of force.
BI-PART DELAY
Set the BI-PART DELAY to
desired setting. The range is 0 to
8 seconds, 0 seconds is OFF.
FORCE AND TIMER TO CLOSE
PROGRAM LIMITS
1. Turn Bi-Part switch to desired setting. Set to “Off” for single
gate applications.
2. Press the “LEARN LIMITS” button.
3. The “SET OPEN LIMIT” LED will blink.
4. Use the “Gate 1” buttons to move Gate 1 to the desired open
position. Repeat if Gate 2 is present using “Gate 2” buttons.
5. Press the “LEARN LIMITS” button to set the Open Limit for
gate(s).
6. The “SET OPEN LIMIT” LED will turn off. The “SET CLOSE
LIMIT” LED will blink.
7. Use the “Gate 1” buttons to move Gate 1 to the desired close
position. Repeat if Gate 2 is present using “Gate 2” buttons.
8. Press the “LEARN LIMITS” button to set the close limit for
gate(s).
9. The “SET CLOSE LIMIT” LED will turn off. The limits are set.
10. Using programmed remote or single button input (SBC) run
the gate(s) from the close limit to the open limit. After
reaching the open limit, run the gate(s) to the close limit.
This will learn the force in the open and close direction.
11. If the learned force is not high enough, manually adjust the
force control as described above.
NOTE: After final limit adjustments the gate can be opened
slightly further by increasing the distance between center of gate
hinge and the gate bracket by 1" (25.4 mm). Do not move the
post bracket assembly.
NOTE: Any following SBC or remote inputs will move the gate.