Nilfisk-ALTO PHH15002A - Manual (Page 2)

Heater Assembly
1. After removing the heater from its carton, carefully inspect
it for possible shipping damage. Return damaged units to
point of purchase.
2. Remove plastic support leg extensions from packaging. Line
up the slots and slide extension into end panels as shown.
(See Figure 1).
Heater Operations
1. The PHH15002 is provided with a POSITIVE OFF
thermostat. In addition to the thermostat, the PHH15002
has a LO/HI heat selection switch.
2. Operation is as simple as A-B-C:
a. Plug heater power supply cord into 120 volt outlet
(see warnings 1, 3, 4, 5 & 6). The rocker switch on
the PHH 15002 will illuminate, indicating power is on.
b. Move heat selection switch to the “LO” position for
750 watts or to the “HI” position for 1500 watts.
c. Rotate the thermostat knob to the right until it stops.
NOTE: You may notice a new smell coming from your
heater during initial use. It should go away within the first
few hours of operation.
3. Allow the heater to operate normally until the room
temperature is comfortable to you. Then simply rotate the
thermostat knob to the left until the thermostat clicks. The
thermostat will then automatically turn your heater on and
off to maintain the room temperature.
4. To adjust the room temperature, rotation of the thermostat
knob to the right will increase the heater output while
rotation of the thermostat knob to the left will decrease the
output. The numbers on the thermostat knob are for
reference only and may help you in setting and adjusting
the heater output for your comfort.
5. To turn heater off, rotate the thermostat knob to the left until
it stops. Always unplug heater when not in use.
Cleaning Instructions
(See Warning No. 11)
1. From time to time, your heater will require cleaning to
remove dust and dirt from the element fins and outlet
air grille. Maintaining a clean heater will help the
heater operate cooler and thus safer.
2. Always turn power off and unplug heater before
cleaning.
3. Use vacuum cleaner with brush attachment to carefully
remove all dust and dirt from element fins and outlet air
grille.
NOTE: Use care not to bend fins while cleaning.
4. To clean painted heater surfaces, use damp cloth only. Do
not use waxes, etc. because they sometimes discolor
due to temperature.
LIMITED WARRANTY
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of pur-
chase, except the element which is warranted for 10 years after purchase. This warranty does not apply to damage from accident, misuse, or alteration;
nor where the connected voltage is more than 5% above the nameplate voltage; nor to equipment improperly installed or wired or maintained in viola-
tion of the product’s installation instructions. All claims for warranty work must be accompanied by proof of the date of installation.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred
to return products to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the
nearest Marley authorized service center or the Marley Engineered Products Service Center, and we will repair or replace, at our option, at no charge
to you with return freight paid by Marley. It is agreed that such repair or replacement is the exclusive remedy available from Marley Engineered Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED AND ALL IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY
DISCLAIMED AND EXCLUDED FROM THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL
DAMAGES ARISING WITH RESPECT TO THE PRODUCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise
returned to the factory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products.
When requesting return authorization, include all catalog numbers shown on the products.
NEED TECHNICAL OR WARRANTY ASSISTANCE?
PLEASE CALL TOLL-FREE 1-800-642-HEAT.
ECR 34741
11/01 5200-2365-002
Correct Incorrect Figure 1
SPX Corporation
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA