Nova-Tech 5095 TRACEABLE COUNTDOWN CONTROLLER - Manual (Page 2)

Traceable ® is a registered trademark of Control Company ©2008 Control Company. 92-5095-00 Rev. 1 051908
COUNT DOWN TIMER (PROGRAM)
The countdown timer function can be used to turn the timer on or off for a period from
1 second up to 23 hours 59 minutes 59 seconds. To set the countdown time, follow the
example shown below. Example: Setting the countdown time to stay on for 1 hour 10
minutes 30 seconds.
● Display the CD PROG using the left or right arrow keys. (While clock is
displayed, push the left arrow key once will display CD PROG.)
● Press the SET key. The word SET will display and either ON or OFF will flash.
● Select ON using the left/right arrow key.
● Press the SET key. Adjust the hour to 1 when the HOUR is flashing using the
left/right arrow keys.
● Press the SET key. Adjust the minute to 10 when the MINUTE is flashing using
the left/right arrow keys.
● Press the SET key. Adjust the second to 30 when the SECOND is flashing using
the left/right arrow keys.
● Press the SET key to complete the setting of countdown time.
The Countdown Timer is now set to turn on or off for 1 hour 10 minutes 30 seconds as
shown in Figure 6. Press the CD key anytime to activate the count down. The display
will show the time counting down when the CD PROG symbol is displayed, until it
reaches zero. When time is up, the time will turn itself off.
The count down will not start when the random function is active. Regular program is
disabled during the count down period. Activating Random function or Manual On/Off
will cancel the count down operation.
DISABLE / MASTER DISABLE FUNCTION
This function allows you to disable and enable any or all of the 14 preset ON/OFF
programs and CD Program using the ON/OFF key.
To disable a program, display the program or CD Program you wish to disable using
the left/right arrow key, then press the SET key. The display is flashing and the word
SET is displayed, press the ON/OFF key to disable the program, the X symbol will
appear to indicate that that particular program is disabled as shown in Figure 7.
Note: The display is still flashing and if there’s no changes to be made on the preset
program, press the SET key, until the display is not flashing. Use this function to
disable as many available preset programs as you choose.
To disable all programs, press the SET key while in clock display. Then press the
ON/OFF key to disable all the preset programs when the display is flashing. The X
symbol will appear on the clock display indicating that all preset programs are
disabled.
Please note that CD Program will not be affected by the master disable.
To cancel the disable function, just repeat the same procedure to turn off the X
symbol.
AUTO-RETURN TO CLOCK DISPLAY
If the unit is left idling more than 1 minute during programming or displaying another
mode, the display will return to clock and the programming operation is cancelled.
However, if the display is showing count down time in progress, auto-return will riot
activate until count down is finished.
LED INDICATOR
The LED indicator shows the status of the timer. If the LED is lit, the timer is on and if
the LED is not lit, the timer is off. Note that the timer’s status can also be seen in the
CLOCK mode, by the word ON or OFF. The LED will only light when the timer is
plugged into an electrical outlet.
RESET
The RESET key is located on the top-right hand corner of the function board. Use a
round object such as a ball-point pen to push the reset key while the SET key is
pressed. Then release the RESET key first before the SET key. After reset, all preset
programs are erased from timer’s memories.
ABNORMAL DISPLAY
When an abnormal display or a blank display appears on the timer, use the above
Reset procedure, otherwise the timer may not work properly. Be sure that the
rechargeable battery Is adequately charged.
WARRANTY, SERVICE, OR RECALIBRATION
For warranty, service, or recalibration, contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail [email protected]
www.control3.com
Control Company is ISO 9001 Quality-
Certified by DNV and ISO 17025 accredited
as a Calibration Laboratory by A2LA.