Foredom H.18SJ - Manual (Page 2)

Maintenance and Lubrication
Handpieces H.18 and H.18SJ never need
lubrication. Putting oil or grease into the
front or back of these handpieces will
damage their pre-lubricated ball bearings.
Flex Shafts: Cleaning and lubrication
should be performed every 50 hours of use:
First be sure to unplug your power tool.
Remove handpiece and then loosen set
screw in motor connector (see previous
page) and remove sheath. The exposed
shaft should be wiped clean with a cloth
and solvent. Apply a light film of Foredom
grease (part no. MS10006) to entire length
of inner shaft. Reconnect shaft and sheath,
following adjustment procedure on previous
page and run motor for ten minutes before
reconnecting handpiece. Turn off motor,
wipe off excess grease from tip of drive
shaft and reconnect to the handpiece.
Collet Replacement Instructions for
H.18, H.18D and H.18SJ Handpieces
Keep a 3/32 ″shank bur with same size
or smaller head in the handpiece.
1. Disassembly of Nose Cone:
Tools required: smooth grip pliers and 1/2 ″
open end wrench.
A. Grasp housing with smooth grip pliers or
firmly grip handpiece at base of
lever assembly.
B. Place 1/2 ″ wrench over flats on nose
cone and unthread.
2. Disassembly of Nosepiece and Collet:
Tools required: pin (3/32 ″ or 2.3mm diameter)
and 1/4 ″ open end wrench.
A. Lock spindle by inserting pin through holes
in handpiece behind lever assembly. You may
need to rotate bur for the pin to go all the
way through.
B. Place 1/4 ″ wrench over flats on nosepiece
and unthread.
C. Remove Collet.
3. Required for Reassembly: pin, 3/32 ″ or
2.35mm diameter bur with head diameter less
than 3/32
″, Foredom Oil MS10010, 1/4″ and
1/2 ″ wrenches, and Replacement Collet HP703.
A. Blow out spindle, replacement collet,
and nosepiece with compressed air.
B. Wipe tapered collet seat clean.
C. Lock spindle by inserting pin through holes
in handpiece rotating bur as needed.
D. Insert pin or bur with small head into
collet. Insert collet with pin into spindle.
E. Hand thread nosepiece over collet and pin or
small bur onto spindle. Place 1/4
″ wrench over
flats and tighten firmly.
F. Place a small drop of Foredom Oil on
nose cone threads. Thread nose cone onto
housing. Tighten with 1/2
″ open end wrench.
4. Collet Inspection:
Depress lever. Bur must enter and exit
collet freely, but not fall out. If collet sticks to
taper in nosepiece or plunger, it will appear
as though bur is stuck. To unseat, simply
push bur in firmly and remove slowly again
while holding lever down. If bur continues to
hang up, remove nose cone and nosepiece,
spread collet fingers, reassemble and test.
Repair Service
Factory repairs are done promptly and at
reasonable cost. If you wish, you can send
your equipment directly to the
factory marked:
“Attention: Service Department”. Be sure
to give your street address, daytime phone
number and/or email address and include
a brief note describing the problem with
the equipment. Estimates will be made
upon request.
Please retain your proof of
purchase for warranty repairs.
For More Information on Foredom machines,
handpieces, or accessories, contact your local
dealer. When no local dealer is available, write:
The Foredom Electric Company
16 Stony Hill Road, Bethel, CT 06801
call: (203) 792-8622, visit our website at:
www.foredom.net or email:
[email protected]
hole nose cone
lever assembly hole bur
pin
LIMITED WARRANTY
Your Foredom Quick Change Handpiece is warrantied against defective material and workmanship
for a period of 90 days from date of purchase. The duplex connection is particularly susceptible to
damage and is not covered by warranty. Replacement duplex springs are shipped with installation
instructions. Blackstone Industries, Inc. d/b/a The Foredom Electric Company warrants, to the
original purchaser only, that its products will be free from defects in material or workmanship for
the applicable period of time indicated above following the purchase date. During the warranty
period, the defective product will be repaired or replaced without charge or, at our sole option, the
purchase price will be refunded. This warranty does not cover damage caused in transit or by
accident, misuse or ordinary wear.
ALL IMPLIED WARRANTIES INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY, ARE LIMITED IN DURATION
TO THE APPLICABLE WARRANTY PERIOD. IN NO EVENT WILL WE BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long
an implied warranty lasts or the exclusion or limitation of incidental or consequential damages,
so the above limitations or exclusion may not apply to you. At our sole option, repair, replacement
or refund will be made if the product is returned postage prepaid to:
The Foredom Electric Company, 16 Stony Hill Road, Bethel CT 06801
All warranty repairs must be done at our factory at the above address. We will not pay any
shipping or transportation charges. Armatures, bearings, shafts, sheaths and duplex springs are
not covered by this warranty.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.