Watlow Series 734 Data Communications - Manual (Page 19)

How to Use Data Communications
19
WATLOW Series 733/734
Name Description Read (?) and/or Write (=) Syntax Range
(data.1) Add ETX & STX with ANSI X3.28 Protocol (data.2)
MDKY Mode Key Action = <sp> MDKY <sp> 1 <cr> 1 = One MODE Key press
MDL Model Number ? <sp> MDL <cr> x1 = 3 or 4; horiz. or vert. unit
Responds 73x-xx-x x2 & x3 = Last two
(See Model # , p. 21) characters of model #, AA-XX
x4 = Software rev; 0-9 or A-X
MENU Menu Step ? <sp> MENU <sp> menu Data entered must be within
<sp> step <cr> individual prompt guidelines,
= <sp> MENU <sp> menu <sp> i.e., SP1 = R1L to R1H, etc.
step <sp> sp1 <sp> sp2 <sp> Enter data for sp2 and events
hours or minutes <sp> minutes or even if they are not available.
seconds <sp> events <cr> See 733/4 Program Manual.
MODE Mode Status ? <sp> MODE <cr> 0 = Operation mode
1 = Program mode
2 = Setup mode
3 = Service mode
4 = Calibration mode
MS Melt Cycle ? <sp> MS <cr> 0 = Melt cycle OFF
= <sp> MS <sp> data.2 <cr> 1 = Melt cycle ON
PB1 Zone 1 Prop Band ? <sp> PB1 <cr> 0 to 999°F
= <sp> PB1 <sp> data.2 <cr> 0 to 555°C
PB2 Zone 2 Prop Band ? <sp> PB2 <cr> 0 to 999°F
= <sp> PB2 <sp> data.2 <cr> 0 to 555°C
0 to 999 Units
RA1 Zone 1 Rate ? <sp> RA1 <cr> 0 to 9.99 minutes
= <sp> RA1 <sp> data.2 <cr>
RA2 Zone 2 Rate ? <sp> RA2 <cr> 0 to 9.99 minutes
= <sp> RA2 <sp> data.2 <cr>
RE1 Zone 1 Reset ? <sp> RE1 <cr> 0 to 9.99 repeats per minute
= <sp> RE1 <sp> data.2 <cr>
RE2 Zone 2 Reset ? <sp> RE2 <cr> 0 to 9.99 repeats per minute
= <sp> RE2 <sp> data.2 <cr>
RH1 Zone 1 Range High ? <sp> RH1 <cr> RL1 to max. INP1 type range
= <sp> RH1 <sp> data.2 <cr>
RH2 Zone 2 Range High ? <sp> RH2 <cr> RL2 to max. INP2 type range
= <sp> RH2 <sp> data.2 <cr>
RL1 Zone 1 Range Low ? <sp> RL1 <cr> Min. INP1 type range to RH1
= <sp> RL1 <sp> data.2 <cr>
RL2 Zone 2 Range Low ? <sp> RL2 <cr> Min. INP2 type range to RH2
= <sp> RL2 <sp> data.2 <cr>
RTD RTD Curve ? <sp> RTD <cr> 0 = DIN
= <sp> RTD <sp> data.2 <cr> 1 = JIS
RUN Menu Run = <sp> RUN <sp> menu <cr> n = Run Menu n
SIL Alarm Silence ? <sp> SIL <cr> 0 = OFF
= <sp> SIL <sp> data.2 <cr> 1 = ON
STAT Run Status ? <sp> STAT <cr> x x; x1=0 idle or 1 run, x2=menu#
STP Maximum Steps ? <sp> STP <cr> 1 = 1 Step
= <sp> STP <sp> data.2 <cr> 2 = 2 Steps
3 = 3 Steps
STOP Menu Stop = <sp> STOP menu <cr> n = Stop Menu n
TCMP Temperature ? <sp> TCMP <cr> 0 = OFF
Compensation = <sp> TCMP <sp> data.2 <cr> 1 = ON
TREM Time Remaining ? <sp> TREM <cr> Learn Menu time remaining
TS Time Select ? <sp> TS <cr> 0 = minutes : seconds
= <sp> TS <sp> data.2 <cr> 1 = hours : minutes
Table 5 -
Command Summary
with Read (?) and
Write (=) Simple
Syntax and Data
Range/Responses.
Commands