Brocade Multi-Service IronWare QoS and Traffic Management Configuration Guide (Supporting R05.6.00) User Manual
Multi-service ironware, Qos and traffic management configuration guide
Advertising
Table of contents
Document Outline
- Contents
- Configuring Traffic Policing for the Brocade NetIron CES and Brocade NetIron CER
- Traffic policing on Brocade NetIron CES and Brocade NetIron CER devices
- Applying traffic policing parameters directly to a port
- Applying traffic policing parameters using a policy map
- Configuration considerations
- Configuring traffic policing
- Configuring a policy-map to remark profile tables
- Configuring port-based traffic policing for inbound and outbound ports
- Using ACLs for filtering in addition to rate limiting
- Displaying rate limiting policies
- Rate limiting BUM packets
- Traffic policing on Brocade NetIron CES and Brocade NetIron CER devices
- Configuring Traffic Policing for the Brocade NetIron XMR and Brocade MLX series
- Traffic policing on the Brocade device
- Applying traffic policing parameters directly to a port
- Applying traffic policing parameters using a policy map
- Configuration considerations
- Configuring traffic policing on Brocade devices
- Using ACLs for filtering in addition to rate limiting
- Configuring for no priority-based traffic policing
- Configuring rate limiting for Copied-CPU-bound traffic
- Displaying rate limiting policies
- IPv6 ACL-based rate limiting
- IPv6 ACL based rate-limiting configuration considerations
- IPv6 ACL based rate-limiting command options
- Configuration Sequence
- Configure inbound rate-limiting on an interface
- Configure outbound rate-limiting on an interface
- Configure strict-ACL rate-limiting on the interface
- Deleting an IPv6 Access-List which is bound to rate-limit
- Configuring rate-limit using non-existing access-list
- Output of show commands to verify output
- Clearing rate-limit counters
- Layer 2 ACL-based rate limiting
- Configuration rules and notes
- Editing a Layer 2 ACL Table
- Define rate limiting parameters
- Binding Layer 2 ACL-based rate limiting policy to a port
- Specifying rate limiting parameters without a policy map
- Display accounting
- Rate limiting protocol traffic using Layer 2 inbound ACLs
- Example of Layer 2 ACL to rate limit broadcast traffic
- Rate limiting ARP packets
- Traffic policing on the Brocade device
- Configuring Quality of Service (QoS) for the Brocade NetIron CES and Brocade NetIron CER Series
- Quality of Service (QoS)
- Ingress Traffic processing through a device
- Forcing the priority of a packet
- Forcing the drop precedence of a packet
- Configuring QoS
- Displaying QoS information
- Scheduling traffic for forwarding
- Egress port and priority based rate shaping
- Example of configuring Prioritized Voice over Data
- Clearing traffic manager statistics
- Network processor counters displayed
- Multicast queue size, flow control, rate shaping and egress buffer threshold
- Ingress traffic shaping per multicast stream
- Implementation considerations
- Configuring multicast traffic policy maps
- Binding multicast traffic policy maps
- Configuration example for rate shaping IPTV multicast stream
- Tuning multicast parameters
- Configuring Quality of Service for the Brocade NetIron XMR and Brocade MLX series
- Ingress Traffic processing through a device
- Creating an Ingress decode policy map
- Forcing or merging the priority of a packet
- Forcing or merging the drop precedence of a packet
- Egress Traffic processing exiting a device
- Creating an egress encode policy map
- Backward compatibility with pre-03.8.00
- Default QoS mappings
- Protocol Packet Prioritization
- Configuring QoS
- Configuring Ingress QoS procedures
- Configuring Egress QoS procedures
- Configuring QoS procedures applicable to Ingress and Egress
- Configuring Ingress decode policy maps
- Binding Ingress decode policy maps
- Configuring a force priority
- Configuring Egress encode policy maps
- Binding an Egress encode EXP policy map
- Enabling a port to use the DEI bit for Ingress and Egress processing
- Specifying the trust level and enabling marking
- Packet mapping commands
- Configuring support for super aggregate VLANs
- Configuring port-level QoS commands on LAG ports
- Displaying QoS information
- Weighted Random Early Discard (WRED)
- Configuring packet drop priority using WRED
- Scheduling traffic for forwarding
- Egress port and priority based rate shaping
- Traffic manager statistics display
- Displaying all traffic manager statistics for a device
- Displaying traffic manager statistics for a port group
- Displaying traffic manager statistics for an interface module
- Displaying traffic manager statistics for NI-MLX-10Gx8-M and NI-MLX-10Gx8-D modules
- Displaying traffic manager statistics for the 4x10G module
- Displaying traffic manager statistics for the 20x1G module
- Displaying traffic manager statistics for IPTV multicast queue
- Clearing traffic manager statistics
- New network processor counters displayed for packets to and from traffic manager
- QoS for NI-MLX-1Gx48-T modules
- Aggregated TM VOQ statistics collection
- Supported modules
- Configuring aggregated TM VOQ statistics collection
- Enabling aggregated TM VOQ statistics collection
- Displaying TM statistics from one queue or all queues
- Displaying TM statistics from the multicast queue
- Showing collected aggregated TM VOQ statistics
- Clearing the TM VOQ statistics
- Displaying TM VOQ depth summary
- Displaying TM buffer utilization
- Clearing TM VOQ depth summary
- Clearing TM buffer utilization
- Displaying QoS packet and byte counters
- QoS commands affected by priority queues
- Enhanced buffer management for NI-MLX-10Gx8 modules and NI-X-100Gx2 modules
- Commands
- Hierarchical Quality of Service (HQoS)