Burcam 300381 C.I. BASE COLUMN SUMP PUMP 1/3HP 115V - Manual (Page 2)

IMPORTANT NOTICE
REPAIR PARTS
REF. PART DESCRIPTION
1 350445 Top Mount Switch
2 350350A 1/3 CV 115V Motor.
3 350456 Motor Bolts (3)
4 350450 Float Rod
5 350447 Rubber Stop (2)
6 350449 Float
7 350446.7 Float/Rod Assembly
8 350443 Float guide
9 350653 Main shaft with coupling
10 350652 Aluminium column
11 350651 C.I. Column Sump Pump Base
MATERIAL REQUIRED FOR
SUMP PUMP APPLICATION
☐ Desired length of 2” ABS pipe.
☐ Elbows and fi ttings to run discharge pipe.
☐ ABS cimentz
☐ 1 2” ABS coupling to connect the pipe
to the check valve.
☐ 1 vertical check valve (350363).
APPLICATION
☐ This domestic sump pump is suitable for application where the total
vertical distance (head) does not exceed 15’. It is designed as an
economic and effi cient means of protecting homes agains water
damage through seepage, where there is no natural drainage.
☐ Capacity: 3000 GPH / 5’ 2500 GPH / 10’ 1600 GPH / 15’.
Locate the rod, the fl oat and the rubber washers in the pump carton. Secure rod’s quide to pump’s
column. Push the rod through the rod guide, then push a rubber washer about six inches from top rod
end. Insert rod end through the top mount switch opening and place the second rubber washer over the
top rod end. Thread the fl oat into the bottom rod end about six to eight turns. Depth of pumping level may
be adjusted by changing the position of the lower rubber rod washer.
Install the required (350363) check valve in the 1 1/2” discharge of the pump’s base. Thread in tightly.
Using 2” ABS coupling and ABS pipes, connect the discharge line to the check valve, and run it to the
desired waste location throught the basement wall of your house. Otherwise, drain hose kits are available
(350354). You may also connect a kit to the check valve with a clamp and run the pipe to the same
location. Be advised that restriction in these kits is important and increase the head of the discharge line.
Position the sump pump in centre of the sump pit (18” diameter X 25” deep). Plug the pump motor three
prong plug/cord into a grounded electrical outlet. Fill the sump pit with water to check pump operation.
Pump should start automatically when the switch lever is activated by the rubber washer and stop when
the water has been discharged and the fl oat returns to the bottom of the sump pit.
STEP 1
STEP 2
STEP 3
FRICTION LOSS IN PIPE NOT INCLUDED
NOTICE
This unit is not designed for applications involving
salt water or brine. Use with salt water or brine will
void warranty.
This product has been designed as a
dewatering pump for fl ood protection in a
residential home. The application of this
product is for permanent installation.
Do not use this pump to pump liquids (water)
in excess of 100 degrees F.
To the end consumer
If you have any problems with the product, before
advising the store, where you’ve purchased the pump,
please contact us at 514 337-4415 , and ask for our sales
department, and they will be pleased to help you with any
questions you might have, concerning your installation.
INSTALLATION STEPS
3
1
2
9
4
10
6
8
5
11
7
Please note before you proceed with the installation of this product that the manufacturer’s
guideline has to be respected. Failure to comply may void your warranty.
The following are minimum requirements in order to protect your residence from fl ooding. It is a small investment but it is
your personal responsibility to protect your home, family and valuables. Failure to comply with the following requirements
may also void your warranty:
• Two (2) pumps have to be installed in the sump pit. The fi rst pump as a primary pump and the second pump as the backup unit.
• Burcam alarm system model 450454 has to be installed to advise you of any malfunctions.
• As sump pumps are electrically powered and activated so to prevent fl ooding, a Burcam battery powered back up pump
model 300403 has to be installed to evacuate the water.
Pump selection, proper and adequate installation are a must to comply with local by-laws and need to be adhered to.