FallTech Beam Anchors - Manual (Page 2)

3
Product Listing
This instruction manual pertains to the use and operation of the
products listed below. Should you have any questions about the product
that you have purchased, please contact FallTech for additional details.
Ratcheting/Sliding Beam Anchors:
Model # Description
Flange
Width
Max. Flange
Thickness
7411 Single-Ratcheting Beam Anchor, Stainless Steel 4” – 12” 1”
7490 Dual-Ratcheting Beam Anchor 3-1/2” – 13” 1-1/4”
7530 Dual-Ratcheting Beam Anchor 4” – 14” 1-1/4”
7531 Single-Ratcheting Beam Anchor 4” – 14” 1-1/4”
Detent-Pin Beam Anchors:
Model # Description
Flange
Width
Max. Flange
Thickness
7485 Detent-Pin Beam Anchor, Small 3-1/2” – 12” 1-1/8”
7486 Detent-Pin Beam Anchor, Large 3-1/2” – 18” 1-1/8”
Fixed-Position Beam Anchors:
Model # Description
Flange
Width
Max. Flange
Thickness
7487 Stationary Beam Anchor, Small 4” – 12” 1-1/8”
7488 Stationary Beam Anchor, Large 4” – 18” 1-1/8”
7533 Hex Bar Beam Anchor, Small 3-1/2” – 12” 1”
7534 Hex Bar Beam Anchor, Large 3-1/2” – 18” 1”
7471 J-Hook Beam Anchor 6” – 16” 1-1/2”
Vertical Beam Anchors:
Model # Description
Flange
Width
Max. Flange
Thickness
7489 Vertical Beam Anchor 2-1/2” – 12” 1-1/2”
7535 Hex Bar Vertical Beam Anchor 4-1/2” – 12” 2”
7536 Hex Bar Vertical Beam Anchor 10” – 24” 2”
Beam Trolley:
Model # Description
Flange
Width
Max. Flange
Thickness
7710 Overhead Beam Trolley 6” – 12” 1-1/2”
4
Section 1: Warnings and Advisories
This product is to be used as a part of a personal fall arrest system,
and should be used only with compatible components. Please see
Advisory #3 in this section for further details. Failure to use
compatible components can result in a failure of the system to
perform as intended, which may result in serious injury or death.
Throughout the OSHA regulations for safety and health, there are
references to Competent Persons and Qualified Persons. ANSI
Z359.0-2007 goes on to further define the roles and qualifications of
these individuals; as well as Authorized Persons, and their
importance in the workplace. These terms are also used in these
instructions. Below is a brief description of the part these
individuals play in the employment of fall protection equipment:
Authorized Person - a person who is exposed to fall hazards during
the course of their work. This individual requires formal training in
the use of personal fall protection equipment and systems. The
term Authorized Person may be used interchangeably with User
and End-User.
Competent Person – a trained and experienced person who is
designated to supervise, implement and monitor an employer’s
managed fall protection program. This individual is capable of
identifying and addressing fall hazards and is authorized to make
decisions and take corrective action in the workplace.
Qualified Person – a person possessing a degree or professional
certificate and having extensive training, knowledge and experience
with fall protection and who is capable of designing and specifying
fall protection equipment and systems to address fall hazards.
Please read these instructions and be sure that you understand
them prior to utilizing this equipment. Also be sure to read the
instructions included with other components which are being
utilized in your Personal Fall Arrest System (Harnesses,
connectors, anchorage connectors, etc.). Failure to understand and
comply with manufacturer’s instructions may result in serious
injury or death. IF YOU DO NOT UNDERSTAND ANY PART OF
THESE INSTRUCTIONS, PLEASE HAVE THEM EXPLAINED TO YOU
BY A COMPETENT PERSON.
This product is to be used as part of a complete fall arrest system in
accordance with industry-recognized best-practices and your
employer’s fall protection plan, as required by the Occupational