FallTech Contractor Series SRL’s - Manual (Page 8)

15
exposed to sharp edges, electrical hazards or prolonged exposure to
highly corrosive environments or substances.
If you have any questions regarding the suitability of this product for
your specific application, please consult with a competent person or
contact FallTech before using. Misuse of this product may result in
serious injury or death.
3.3: Restricted Applications
Leading-Edge Work: This product is not suitable for leading-edge work
except in the case of residential roofing applications.
Offshore Oil Rigs: This product is not suitable for offshore drilling
applications where there will be prolonged exposure to the corrosive
exposure to sea air and/or salt water.
Harsh Chemical Environments: Acids and other caustic chemicals can
cause damage to this SRL and its components. Damage from chemical
exposure can be difficult to detect and FallTech recommends frequent
replacement and/or factory service.
Arborist Applications: This product should never be used in arborist
applications or tree-trimming applications.
Aerial Lifts: This product is not approved for use in aerial lifts, bucket
trucks or scissor lifts.
Extended Free-Falls: Except for residential roofing applications, this
product should not be used in applications where free-fall exceeds 2’ (2
feet).
Heavyweight: This product should not be used in applications where the
total weight of the user (including clothing, tools and equipment) exceeds
310 lbs.
Power Transmission: Use of this product in areas where the lifeline may
come in contact with electrical hazards is prohibited. FallTech
recommends the use of Aramid webbing SRL’s (Kevlar®, Nomex® or
Dyneema®) for these applications.
Welding: Use of this product in areas where the lifeline may come in
contact with high heat or welding slag is not recommended. FallTech
recommends the use of Aramid webbing SRL’s (Kevlar®, Nomex® or
Dyneema®) for these applications.
16
3.4: Installation and Use
1. Select the appropriate FallTech Contractor SRL based on the
work conditions and distance needed of unhindered vertical
travel. Be sure not to operate with the cable at full extension.
FallTech recommends operating at with a maximum of 90% of
the cable extended to ensure proper deceleration in the event of
a fall.
2. Read, understand and comply with manufacturer’s instructions
for each component of your Personal Fall Arrest System (Full-
Body Harness, Anchorage Connectors, etc.). Be sure to choose
components that are compatible with this SRL. If you have
questions about product or component compatibility, be sure to
contact FallTech for additional instructions.
3. Calculate possible swing fall hazards, total fall distance, and
required clearance distance. If you have a swing-fall hazard or
do not have the required clearance distance, STOP and
reevaluate your application and system. Your work location
should never exceed an angle of 15 degrees in any direction in
relation to your SRL’s anchorage location.
4. Attach the SRL by connecting a double-locking carabiner to top
end of the unit. Ensure that the carabiner is properly
dimensioned to join the SRL to the anchorage connector or
bracket. If either the SRL or the anchorage interferes with the
operation of the carabiner gate, use a larger carabiner. Hang the
unit from an approved anchorage capable of supporting a
minimum of 5,000 lbs. (or 3,600 lbs with the certification of a
qualified person). This should be done without exposing anyone
to a fall hazard. The anchorage should be at a minimum height
so that the attachment connector of the SRL is even with, or
above, the back D-ring of your full body harness. Ensure that
the connector gate is closed and locked once the SRL has been
mounted to the anchorage.
5. If the SRL is to be remotely mounted, attach a tagline to the end
of the lifeline. This tagline allows access to the lifeline of a
remotely mounted FallTech SRL and allows the lifeline to be
retracted completely back into the housing in a controlled
manner without hazardous “Free Wheeling”.
6. Detach the tagline to avoid tangling. Do not leave the tagline
attached to the SRL while you are using it.
7. Before use, be sure to inspect in accordance with the
instructions in section 8-B of this manual. Test for proper
braking action by grasping the lifeline and pulling down hard,
ensuring that the unit locks.