Star Water Systems 423750 - Manual (Page 2)

© Copyright 2008. All rights reserved.
GENERAL INFORMATION
1. These pumps are equipped with an omnidirectional mechanical
float switch. The pump will turn on automatically when the water
level in the sump reaches approximately the float switch "on"
level and automatically turn off when the water is pumped down
to the float switch "off" level. See Chart A for details.
2. The sump pit must be a minimum of 18" deep and 12" in diam-
eter. The pump requires a minimum diameter of 12" so that the
float switch will operate without restriction. Any smaller diameter
may restrict the switch operation, resulting in pump failure.
INSTALLATION
1. For your safety, turn off the electrical power at the service en-
trance to avoid any possible electrical shock hazards.
2. On a replacement installation, remove the existing pump from
the sump by disconnecting the discharge pipe or hose from the
old pump. Depending on how your old pump is installed, unscrew
clamps and discard old corrugated hose, or unscrew galvanized
or plastic pipe from pump discharge. If discharge pipe cannot be
removed easily, saw through the pipe about five feet above the
pump discharge.
3. After removing the old pump, remove sediment, debris, and any
standing water from the sump pit.
4. Place your pump in the sump and attach the discharge piping. Be
sure that the pump is positioned so that the float switch moves
freely without touching the wall of the sump or other obstructions.
(See Fig. 1).
5. Install a full flow check valve to prevent back flow which can
cause the pump to cycle too frequently and result in wear and
shortened motor life. Drill 3/16" vent hole in piping below the pit
cover and check valve. Water stream will be visible from this hole
during pump run periods. Reattach discharge piping as required.
6. Do not allow the cord to interfere with the float control motion or
to drape over the pump motor. With electrician's tape, secure the
cord to the discharge pipe. This will provide protection for the
cord and make a neat installation.
7. Plug in pump and restore electrical power at the service entrance.
Fill sump pit with water to check automatic switch operation.
8. Install a sump cover. A cover will prevent solid matter from falling
into the sump, prevent odors, and guards against accidental
injury.
G.F.C.I.
CHECK VALVE
VENT HOLE
12" DIA.
22"
OFF LEVEL
ON LEVEL
ILO463
Pump On / Off Levels Chart A
Float
Switch
Pump Model
3SDHL / 451521 3STS 5STS / 423750
On Level 11-1/4" 10-12" 10-12"
Off Level 4-1/8" 5-1/2" 5-1/2"
PERFORMANCE
Your pump will operate effectively pumping clear, storm and drain
waters. Although it will usually pass small particles suspended in wa-
ter - grass, heavy mud, sand or pea gravel can clog the pump and
reduce the pump's performance. This can usually be cleaned out
by back-flushing on pump side of check valve with a garden hose
through the discharge.
This product is warranted for one year from the date of purchase or two years
from the date of manufacture, whichever occurs first. Subject to the condi-
tions hereinafter set forth, the manufacturer will repair or replace to the original
consumer, any portion of the product which proves defective due to defective
materials or workmanship. To obtain warranty service, contact the dealer from
whom the product was purchased. The manufacturer retains the sole right and
option to determine whether to repair or replace defective equipment, parts or
components. Damage due to conditions beyond the control of the manufacturer
is not covered by this warranty.
THIS WARRANTY WILL NOT APPLY: (a) To defects or malfunctions resulting from
failure to properly install, operate or maintain the unit in accordance with printed
instructions provided; (b) to failures resulting from abuse, accident or negligence;
(c) to normal maintenance services and the parts used in connection with such
service; (d) to units which are not installed in accordance with normal applicable
local codes, ordinances and good trade practices; and (e) the unit is used for
purposes other than for what it was designed and manufactured.
RETURN OF WARRANTED COMPONENTS: Any item to be repaired or replaced
under this warranty must be returned to the manufacturer at Kendallville, Indiana
or such other place as the manufacturer may designate, freight prepaid.
LIMITED WARRANTY
THE WARRANTY PROVIDED HEREIN IS IN LIEU OF ALL OTHER EXPRESS
WARRANTIES, AND MAY NOT BE EXTENDED OR MODIFIED BY ANYONE.
ANY IMPLIED WARRANTIES SHALL BE LIMITED TO THE PERIOD OF THE
LIMITED WARRANTY AND THEREAFTER ALL SUCH IMPLIED WARRANTIES
ARE DISCLAIMED AND EXCLUDED. THE MANUFACTURER SHALL NOT, UNDER
ANY CIRCUMSTANCES, BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO DAMAGE TO, OR LOSS
OF, OTHER PROPERTY OR EQUIPMENT, LOSS OF PROFITS, INCONVENIENCE
, OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY TYPE
OR NATURE. THE LIABILITY OF THE MANUFACTURER SHALL NOT EXCEED
THE PRICE OF THE PRODUCT UPON WHICH SUCH LIABILITY IS BASED.
This warranty gives you specific legal rights, and you may have other rights
which vary from state to state. Some states do not allow limitations on duration
of implied warranties or exclusion of incidental or consequential damages, so
the above limitations may not apply to you.
FOR YOUR WARRANTY PROTECTION, THE WARRANTY REGISTRATION
MUST BE COMPLETED AND RETURNED TO THE WARRANTY INFORMA-
TION CENTER WITHIN TEN DAYS OF INSTALLATION. WARRANTY VALID
IN CANADA AND MEXICO.