WEN 100T1 100W Soldering Gun - Manual

®
USER’S MANUAL
1. Using the Cord (#6), connect the gun to a
120V/60Hz power supply.
2. Holding the gun by the Handle (#5) place the Solder
Tip (#1) on the point you wish to solder.
3. Turn on the Switch (#4) and the Light (#3) will
shine on.
4. It will take 6 to 8 seconds for the gun to reach
temperature (446 degrees F).
5. When finished soldering, turn off the Switch (#4).
As you depress the Switch (#4) the gun will continue
to heat up. Do not depress the Switch (#4) for long
periods of time while soldering.
When you let go of the Switch (#4), the temperature
diminishes quickly. Depressing the Switch (#4) quickly
raises the temperature.
Keeping the gun at a constant temperature extends
the life of the gun.
Before using the gun, lubricate the Soldering Tip (#1).
This gun is energy efficient as it reaches temperature
very quickly.
The shape of the Soldering Tip (#1) allows you to
partially contact the workpeice.
MAiNtENANcE
The gun and the Soldering Tip (#1) are designed to
easily disconnect for occasional replacement.
tip REpLAcEMENt
Unscrew the two screws connecting the Soldering
Tip (#1) to the gun. Pull off the old tip, replace it, and
replace the two screws.
SpEcific SAfEty RULES
1. Before using, verify the electricity requirements and
visually inspect the gun and your work stand.
2. Never use the gun in the rain or damp locations.
3. Make sure no foreign objects are in the gun’s
internal parts.
4. Never dismantle the gun. Contact an authorized
service technician.
5. Disconnect the gun from the power source when
not in use.
6. This gun is primarily designed for indoor use.
SAfEty iNStRUctioNS
Warning, when using electric tools basic safety
precautions should be followed to reduce the risk of
fire, electric shock, and personal injury. Read the entire
manual before attempting to operate the soldering gun.
Save this manual.
1. Keep work area clean, cluttered areas and benches
invite injuries.
2. Examine your work area, never expose power tools
to rain. Do not use power tools in damp or wet loca-
tions. Keep work area well lit. Don’t use power tools
near flammable liquids or gasoline.
3. Guard against electric shock, prevent body contact
with grounded surfaces (pipes, radiators, ranges,
refrigerators) when open operating power tools.
4. Keep children away from power tools, do not let
anyone contact the tool or the power cord. Keep
all visitors out of the work area.
5. Store idle tools, when not in use, tools should be
stored in a dry, out of reach, or locked location,
away from children.
6. Do not force tool, it will operate more efficiently and
safer at the normal rate it was designed for.
7. Use right tool, don’t force small tools to do the job of
heavy tools. Operate tools for intended use only.
8. Dress properly, do not wear loose clothing or
jewelry. They may become caught in moving parts.
Rubber gloves and non-skid footwear are recom-
mended when working outdoors. Wear a protective
hair covering to contain long hair.
9. Use proper safety glasses, if necessary, use a
face shield or dust mask.
10. Don’t abuse cord, never carry the tool by the cord
or yank it out of a power receptacle. Keep cord
away from heat, all liquids, and sharp edges.
Operators Manual
Model 100T1
100W
Soldering Gun
SpEcificAtioNS
Power 100W
Voltage 120V~
Frequency 60Hz
Insulation Class II
Important
Your new tool has been engineered and
manufactured to WEN’s
® high standards
for dependability, ease of operation, and
operator safety. Properly cared for, it will
give you years of rugged, trouble-free
performance.
Pay close attention to the Rules for Safe
Operation, Warnings, and Cautions. If you
use your tool properly and only for what
it is intended, you will enjoy years of safe,
reliable service.
Before using the Gun, make sure your
voltage and electric current frequency
match with the technical information
above. The numbers shown here refer
to the illustration above.
1. Soldering Tip
2. Screw
3. Light
4. Switch
5. Handle
6. Power Cord
6
5
4
3
2
1