Connection diagrams, Cold water models only, Diagram 1: single sensor diagram 2: dual sensor – Seametrics MJ-Series User Manual

Page 4: Hot water models only, Hot water models only ¾” 1

Advertising
background image

1

2

3a

or

3b

4

5

11

10

12

9a

or

9b

6

7

8 a-c

LT-65200120-052714

05/27/2014

Seametrics Incorporated • 19026 72nd Avenue South • Kent, Washington 98032 • USA

(P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • www.seametrics.com

CONNECTIONS, MAINTENANCE and REPAIR

Page

MJ-SERIES PARTS

COLD WATER MODELS ONLY

1½”

2”

1

Lid and Hinge Pin Assembly

101070

101070

2

Lens Gasket Assembly

101085

101085

3

a

Internal Assembly (gallons)

101075

101076

b

Internal Assembly (cubic feet)

101079

101081

4

Coupling Assembly (incl 2 sets)

101303

101304

5

Coupling Gasket Assembly (incl 2)

101083

101084

6

Lens

101004

101004

7

Sensor Screw

101045

101045

8

a

Single Reed Switch Sensor (MJR)

100980

100980

b

Double Reed Switch Sensor (MJR)

100993

100993

c

Single Hall-Effect Sensor (MJE)

101065

101065

9

a

Register (gallons)

100999

100999

b

Register (cubic feet)

101008

101009

10

Internal Strainer

101044

101044

11

Tubular Strainer

101031

101032

12

Register Gasket

102228

102228

INTERNAL PARTS REPLACEMENT.

All of the internal parts of

an MJ-Series meter lift out as a unit, after the top has been

unscrewed. The lens can then be removed and the internal as-

sembly lifted out. If necessary, turn the meter upside down and

tap one end lightly on a countertop to loosen the internals. The

assembly can be separated by hand.

Blue - (No Connection)

Black - Common

Red - N O

Black - Common

Red - N O

Blue - N O

CONNECTION DIAGRAMS

Diagram 1: Single Sensor

Diagram 2: Dual Sensor

NOTE:

The Dual Sensor is distinguished by a red stripe on the cable at the

base of the sensor.

MJE or MJHE:

Hall-Effect

NOTE:

MJ(H)E not available with dual sensor

MJR or MJHR:

Reed Switch

MJR or MJHR:

Reed Switch

Black ( - )

White (signal)

Red (+)

To Distinguish Single Sensor From Dual:

Single:

(if new from factory) blue wire is cut back on cable end.

Dual:

A red stripe will be on cable near sensor.

Note:

Dual sensor can be used as a single sensor also - use either the red OR

the blue wire w/black. If using it as a dual sensor then connecting red and blue
together will produce two pulses with every revolution of magnet.

COLD WATER MODELS ONLY

¾”

1”

1

Lid and Hinge Pin Assembly

101068

101069

2

Lens Gasket Assembly

101071

101072

3

a

Internal Assembly (gallons)

101073

101074

b

Internal Assembly (cubic feet)

101077

101078

4

Coupling Assembly (incl 2 sets)

101301

101302

5

Coupling Gasket Assembly (incl 2)

101081

101082

6

Lens

101004

101004

7

Sensor Screw

101045

101045

8

a

Single Reed Switch Sensor (MJR)

100980

100980

b

Double Reed Switch Sensor (MJR)

100993

100993

c

Single Hall-Effect Sensor (MJE)

101065

101065

9

a

Register (gallons)

100997

100998

b

Register (cubic feet)

101006

101007

10

Internal Strainer

101016

101043

11

Tubular Strainer

101029

101030

12

Register Gasket

101013

101027

HOT WATER MODELS ONLY

1½”

2”

1

Lid and Hinge Pin Assembly

101356

101356

2

Lens Gasket Assembly

101334

101334

3

a

Internal Assembly (gallons)

101352

101353

b

Internal Assembly (cubic feet)

101348

101349

4

Coupling Assembly (incl 2 sets)

101303

101304

5

Coupling Gasket Assembly (incl 2)

101083

101084

6

Lens

101004

101004

7

Sensor Screw

101045

101045

8

a

Single Reed Switch Sensor (MJR)

100980

100980

b

Double Reed Switch Sensor (MJR)

100993

100993

c

Single Hall-Effect Sensor (MJE)

101065

101065

9

a

Register (gallons)

101374

101375

b

Register (cubic feet)

101370

101371

10

Internal Strainer

101381

101381

11

Tubular Strainer

101384

101385

12

Register Gasket

101341

101341

HOT WATER MODELS ONLY

¾”

1”

1

Lid and Hinge Pin Assembly

101354

101355

2

Lens Gasket Assembly

101332

101333

3

a

Internal Assembly (gallons)

101350

101351

b

Internal Assembly (cubic feet)

101346

101347

4

Coupling Assembly (incl 2 sets)

101301

101302

5

Coupling Gasket Assembly (incl 2)

101081

101082

6

Lens

101004

101004

7

Sensor Screw

101045

101045

8

a

Single Reed Switch Sensor (MJR)

100980

100980

b

Double Reed Switch Sensor (MJR)

100993

100993

c

Single Hall-Effect Sensor (MJE)

101065

101365

9

a

Register (gallons)

101372

101373

b

Register (cubic feet)

101372

101373

10

Internal Strainer

101379

101380

11

Tubular Strainer

101382

101383

12

Register Gasket

101339

101340

Advertising