Badger Meter 380 Series Btu System - Manual (Page 11)

Page 11 7-11
Installation & Operation Manual
SPECIFICATIONS
Sensor Assembly:
Housing: PEEK
Impeller: 316SS
Shaft: Tungsten Carbide
CS Specific: Torlon ® Bearing, EDPM O-Rings
HS Specific: Ketron ® Bearing, Aflas ® O-Rings
Tee: Cast Bronze
ENVIRONMENTAL
Fluid Temp. -4°F to 140°F (-20°C to 60°C) - chilled
40°F to 260°F (4°C to 125°C) - hot
Ambient Temp. -4°F to 150°F (-20°C to 65°C)
Pressure Ratings:
Badger Data Industrial Series 380 BTU Systems
Specifications
MECHANICAL
Sensor Assembly Mass < 15lb
Houseing: PEEK
Impeller: 316SS ELECTRICAL
Shaft: Tungston Carbide Inputs
CS Specific: Torlon Bearing, EDPM O‐Rings Power 12‐35VDC
HS Specific: Ketron Bearing, Aflas O‐Rings 9‐28VAC rms
Communication Modbus
Tee BACnet
Cast Bronze Output
Scaled Pulse Open Drain
Temperature Rating For Wetted Materials
CS: ‐20F to 180F MATERIALS
HS: 30F to 250F Housing Polycarbonate
Flow Sensor PEEK
Ambient Temperature Rating Potting Material Polyurethane
‐20C to 65C Tee Brass
Pressure Ratings Sensor Body Sizes
Tee Sizes 0.75", 1", 1.25", 1.5", and 2"
Recommended Design Flow Range
1 to 15 FPS
380CS and 380HS*
Temp** F
Temp F PSIG Type Range COMMENTS
40 400 380CS -20 > +180 Torlon Brgs & EPDM seals
60 400 380CS -20 > +180 Torlon Brgs & EPDM seals
80 400 380CS -20 > +180 Torlon Brgs & EPDM seals
100 380 380CS -20 > +180 Torlon Brgs & EPDM seals
120 365 380CS -20 > +180 Torlon Brgs & EPDM seals
140 350 380CS -20 > +180 Torlon Brgs & EPDM seals
160 340 380CS -20 > +180 Torlon Brgs & EPDM seals
180 320 380CS -20 > +180 Upper Limit for Torlon & EPDM
200 300 380HS +30 > +250 Ketron Brgs & Aflas seals***
220 280 380HS +30 > +250 Ketron Brgs & Aflas seals
240 260 380HS +30 > +250 Ketron Brgs & Aflas seals
250 230 380HS +30 > +250 Ketron Brgs & Aflas seals
*Rating is based on PvT of Brass RTD fitting.
**Non-Freezing.
***Special: Ketron Brgs & EPDM seals for < +30F.
Accuracy
Flow Calculation: ±1% of Rate
Temperature Calculation: ±1%
BTU Calculation: ±1%
Output Pulse Width
10, 50, 150, 200, or 250mS
Put Image of Dimentional Drawing here
380CS and 380HS*
Temp** F
Temp F PSIG Type Range COMMENTS
40 400 380CS -20 > +180 Torlon Brgs & EPDM seals
60 400 380CS -20 > +180 Torlon Brgs & EPDM seals
80 400 380CS -20 > +180 Torlon Brgs & EPDM seals
100 380 380CS -20 > +180 Torlon Brgs & EPDM seals
120 365 380CS -20 > +180 Torlon Brgs & EPDM seals
140 350 380CS -20 > +180 Torlon Brgs & EPDM seals
160 340 380CS -20 > +180 Torlon Brgs & EPDM seals
180 320 380CS -20 > +180 Upper Limit for Torlon & EPDM
200 300 380HS +30 > +250 Ketron Brgs & Aflas seals***
220 280 380HS +30 > +250 Ketron Brgs & Aflas seals
240 260 380HS +30 > +250 Ketron Brgs & Aflas seals
250 230 380HS +30 > +250 Ketron Brgs & Aflas seals
*Rating is based on PvT of Brass RTD fitting.
**Non-Freezing.
***Special: Ketron Brgs & EPDM seals for < +30F.
Figure 7: 380 CS & HS Pressure Ratings
MECHANICAL
Mass: Less than 13 lbs.
ELECTRICAL
Inputs
Power: Isolated 12-24 V DC/V AC ±10%
RS-485 is non-isolated to prevent ground faults. Do not share power with other devices.
Badger Meter A1028 plug-in type 120 VAC/12 V DC power supply recommended.
Communication: Modbus RTU
BACnet MSTP
Output
Scaled Pulse: Open Drain
0.01 Hz min. to 100 Hz max.
MATERIALS
Housing: Polycarbonate
Flow Sensor: PEEK
Potting Material: Polyurethane
Tee: Brass