Blue-White A-100N FLEXFLO Peristaltic Pump - Manual (Page 16)

6.5 Mode 3 - 0-10V DC input - In this mode, the on-time of the cycle
will automatically adjust to match the received VDC input value. When the
VDC value is equal the programmed maximum, the pump will run
continuously.
Four values must be programmed:
1) ON-T = The amount of time the pump will run, per cycle, when the
minimum VDC value is received. (Typically programmed to zero)
2) VDC minimum = The VDC input value that will result in the on time
(ON-T). (Typically programmed to 0 VDC)
3) TOT-T = The total cycle time.
4) VDC maximum = The VDC input value that will result in the pump
running continuously.
Example:
ON-T setting = 0 seconds
VDC minimum setting = 0 VDC
TOT-T setting = 6 seconds
VDC
maximum setting = 7.5 VDC
A-100NE
Page 16
RUN
PROGRAM
STAND-BY
PRIME
MINIMUM
MAXIMUM
3
00.0
MODE
ON-T SEC
+ Set the pump for mode 3. Press the
MODE button until MODE 3 is shown on
the LCD display.
+ Enter the programming mode. At the
same time, press the RUN/STANDBY
button and the MODE button. A blinking
ARROW will point to the word
PROGRAM indicating the program mode
has been activated. The on time ON-T
icon will blink. The currently selected time unit icon will be displayed.
The current on time setting will be displayed and the left most (selected)
digit will blink. The decimal is fixed and cannot be moved.
+ Pressing the DIGIT button will increase the selected digit.
+ Pressing the FIELD button will select a new the digit to the right or the
time unit.
+ Press the DIGIT button to increase the selected digit or time unit.
1 0 2 3 5 6 7 8 10
0
1.5
3.0
4.5
6.0
Pump Run-T
ime (Sec.)
DC voltage input (VDC)
4 9
A-100NE
Page 17
RUN
PROGRAM
STAND-BY
PRIME
MINIMUM
MAXIMUM
3
00.0
MODE
SEC TOT-T
+ Press the MODE button to exit the on time
programming screen and enter the
minimum programming screen. The VDC
icon will blink. A blinking ARROW will
appear next to the word MINIMUM. The
current minimum VDC setting will be
displayed and the left most (selected) digit
VDC
will blink.
+ Pressing the DIGIT button will increase the selected digit.
total time TOT-T icon will blink. The currently selected time unit icon will
be displayed. The current total time setting will be displayed and the left
most (selected) digit will blink. The decimal is fixed and cannot be
moved.
+ Pressing the DIGIT button will increase the selected digit.
+ Pressing the FIELD button will select a
new the digit to the right.
+ Press the DIGIT button to increase the
selected digit.
+ Press the MODE button to exit the VDC
minimum programming screen and enter
the total time programming screen. The
+ Pressing the FIELD button will select a
new the digit to the right or the time unit.
+ Press the DIGIT button to increase the
selected digit or time unit.
+ Press the MODE button to exit the total
time programming screen and enter the
VDC maximum programming screen. The
VDC icon will blink. A blinking ARROW
will appear next to the word MAXIMUM. The current maximum VDC
setting will be displayed and the left most (selected) digit will blink.
+ Pressing the DIGIT button will increase the selected digit.
+ Pressing the FIELD button will select a new the digit to the right.
+ Press the DIGIT button to increase the selected digit.
+ At the same time, press the RUN/STANDBY button and the MODE
button. A blinking ARROW will point to the word RUN indicating the run
mode has been activated.
RUN
PROGRAM
STAND-BY
PRIME
MINIMUM
MAXIMUM
3
9.5
MODE
VDC
RUN
PROGRAM
STAND-BY
PRIME
MINIMUM
MAXIMUM
3
0.0
MODE
VDC