Blue-White A-100N FLEXFLO Peristaltic Pump User Manual
Page 2
TABLE OF CONTENTS
1.....Introduction .....................................................................................3
2.....Specifications............. .............. .............. .............. .............. ..............3
3.....Features........ .............. .............. .............. .............. .............. ..............3
4.....Unpacking.... .............. .............. .............. .............. .............. ..............3
5.....Installation ... .............. .............. .............. .............. .............. ..............4
5.1..Mounting location ............. .............. .............. .............. ..............4
5.2..Input power connections ... .............. .............. .............. ..............5
5.3..External input signal connections.... .............. .............. ..............6
5.4..How to install the tubing and fittings............. .............. ..............8
6.....How to operate the A-100N ..... .............. .............. .............. ..............9
6.1..Pump output controls ........ .............. .............. .............. ..............9
6.2..Mode 0 - TFD and FVS System set-up.......... .............. ..............10
6.3..Mode 1 - Manually Adjusting the output....... .............. ..............12
6.4..Mode 2 - 4-20 mA input.... .............. .............. .............. ..............14
6.5..Mode 3 - 0-10 VDC input . .............. .............. .............. ..............16
6.6..Mode 4 - Frequency (Hz) input ....... .............. .............. ..............18
6.7..Mode 5 - Pulse input (Batch)........... .............. .............. ..............20
7.....How to maintain the A-100NE. .............. .............. .............. ..............21
7.1..Routine inspection and cleaning...... .............. .............. ..............21
7.2..How to clean and lubricate the A-100N......... .............. ..............21
7.3..500 hour service warning timer ....... .............. .............. ..............21
7.4..How to replace the pump tube......... .............. .............. ..............22
Replacement parts drawing ...... .............. .............. .............. ..............24
Replacement parts list .............. .............. .............. .............. ..............25
Warranty information. .............. .............. .............. .............. ..............26
Authorized service centers ....... .............. .............. .............. ..............27
A-100NE
Page 2
2.0 Specifications
Maximum Working Pressure
100 psig / 6.9 bar (most models)
o
o
Maximum Fluid Temperature
130 F / 54 C
o
o
Ambient Temperature Range
14 to 110 F / -10 to 43 C
Duty Cycle
Continuous
Maximum Solids
50% by volume
Maximum Viscosity
5,000 Centipoise
Maximum Suction Lift
up to 30 ft. water
Power Requirements
115V60Hz 80 Watts,
220V50Hz 40 Watts,
230V60Hz 45 Watts
Dimensions
6-1/8” H x 10-1/8” W x 9” D
Weight
8 lb.
4.0 Unpacking
Your pump package should contain the following:
1 - Injector pump with 2 pump tube assemblies
1 - suction tube strainer
1 - ceramic tubing weight
1 - 5’ Length of clear PVC suction tubing
1 - 5’ Length of opaque LLDPE discharge tubing
1 - Injection fitting with internal back-flow check valve
1 - Mounting hardware kit
1 - Shroud (weather proof cover see page 10)
3.0 Features
!
Peristaltic Pump Tube does not require valves.
!
Self priming. Cannot vapor lock.
!
High outlet pressure capability of 100 psig.*
!
High inlet suction lift capability of 30 feet.
!
Patented Tube Failure Detection (TFD)system.
!
Patented pump tube assembly design.
!
Digital electronic feed rate control.
!
Pump Tube service warning timer.
!
Corrosion proof Valox housing.
!
Tamper resistant electronic control panel cover.
A-100NE
Page 3
1.0 Introduction
Thank you for purchasing the A-100N Model E Peristaltic Metering Pump.
The A-100N is designed to inject chemicals into piping systems. The pump
has been tested by NSF International for use with 12 ½% Sodium
Hypochlorite. The Model E is equipped with external input control circuitry
which allows the pumps output to be externally controlled by either a 4-
20mA input signal, a 0-10V DC input signal or a pulsed input signal.