Night Guard Home Surveillance System C3-RS-601 User Manual
Page 12
7/9/2008
RS-603 REV A.
12
FEATURE “III” PROGRAMMING:
Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
1. Push the Valet switch 3 times (holding in on the 3
rd
push ) until three chirps with one long chirp is heard, then release
the valet switch. You are now in the Alarm feature “A” programming mode.
2. Press and release the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two
pulse
Three Chirps /
LED three pulse
Four Chirps /
LED four pulse
1.
20 minutes run time
10 minutes
run time
30 minutes run
time
5 minutes run time
2.
0.8-second Door lock & Unlock.
3.5-second
Door
Lock &
Unlock.
0.8 second lock,
0.35 second
unlock
0.8 second dbl
lock,0.8 second dbl
unlock
Five chirps= 0.8 second lock, dbl 0.8 second unlock
Six chirps= dbl 0.8 second lock, 0.8 second unlock
3.
+
Door Lock before
start
Door Lock after
start
Door Lock before & after start *
This is the preferred setting when
using the optional XT-11 single
button remote
Without this
feature
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE “IV” PROGRAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 4 times (holding in on the 4
th
push ) until four chirps with one long chirp is heard, then release
the valet switch. You are now in the Alarm feature “A” programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two
pulse
Three Chirps /
LED three pulse
Four Chirps / LED four
pulse
1.
Tachometer checking type.
Voltage
checking type
Timer checking
type
DBI TACH **
DATA ONLY !!
2.
RPM learning
Start Timer:
0.6-second
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4
chirps), 1.4-second (5 chirps), 1.6-second (6 chirps),
1.8-second (7 chirps), 2.0-second (8 chirps), 3.0-second (9
chirps), 4.0-second (10 chirps),
3.
+
Low check level
Hi check level
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE “V” PROGRAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 5 times (holding in on the 5
th
push ) until five chirps with one long chirp is heard, then release
the valet switch. You are now in the Alarm feature “A” programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
Four Chirps / LED
four pulse
1.
Second Accessory
H3/9 Blue/Black
Second Start
H3/9 Blue/Black
2.
+ 50 RPM
DBI ONLY
No RPM learning
3.
+
- 50 RPM
DBI ONLY
No RPM Learning or < 50RPM
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.