LG LSC27937SB - Manual (Page 15)

15
USING YOUR REFRIGERATOR
LIGHT/FILTER
The LIGHT/FILTER button controls the lamp in the
dispenser, resets the water filter replacement indicator
when the filter has been replaced.
The water filter needs replacement once every six months.
Filter month indicator becomes “0” to let you know when
replace filter.
Press and hold the LIGHT/FILTER button for more than 3
seconds to reset the filter month indicator to six after the
water filter has been replaced.
ALARM/LOCK
Press this button to control the door-open alarm. Press
and hold the ALARM/LOCK button for 3 seconds to lock
the dispenser and all the other control panel functions.
Press and hold again for 3 seconds to unlock. The
ALARM/LOCK button also controls the door alarm
that sounds three times in 30 seconds intervals when a
compartment door is left open for more than 60 seconds.
The alarm stop sounding when the door is closed. Press
the ALARM/LOCK button once to activate or deactivate
the door alarm function.
DISPLAY OFF MODE
To activated Display Off Mode press and hold ICE PLUS
and FREEZER key over 5 seconds until lights will turn on
and after 20 seconds of inactivity the lights will turn off
automatically.
To exit Display Off Mode press and hold ICE PLUS and
FREEZER key over 5 seconds until lights will tilt. Display
Off Mode does not affect the temperature control
settings of the unit.
Ice Type Indicator
Shows the type of ice,
crushed or cube, or water that
the dispenser will dispense.
Freezer Temperature
Shows the temperature in the
freezer, Celsius or Fahrenheit.
Refrigerator Temperature
Shows the temperature in
the refrigerator, Celsius or
Fahrenheit.
Ice Plus
When this button is on the screen will show this has been
activated.
Dispenser Light
When this button is in function on the light will show this
has been activated. When the dispenser light is on the
display will indicate this feature.
Door Alarm Indicator
This indicator shows that the door-open warning alarm
is activated.
Water Filter Status
This light shows the filter’s status. See the filter’s
configurations.
Lock Status
This light shows the actual status of the control panel, in
which the lock function is on.
DIAGNOSIS FUNCTION (FAILURE DETECTION)
Diagnosis function automatically detects failure during
the normal use of refrigerator.
If you refrigerator fails, do not turn off the power. Instead,
contact a local Authorized service center or call our
support line for assistance. Turning off the appliance
will make it more difficult for the service technician to
determine the problem.
ADJUSTING CONTROL SETTINGS
Give the refrigerator time to cool down completely
before making final adjustments. It is best to wait 24
hours before doing this. The initial settings mentioned
in “Control Panel Features” section should be correct for
normal household refrigerator use.
The refrigerator control functions as the thermostat for
the entire appliance (refrigerator and freezer sections).
The colder the setting, compressor will the longer the
run to keep the temperature colder. The freezer control
adjusts the cold air flow from the freezer to the refrigerator.
Setting the freezer control to a lower temperature keeps
more cold air in the freezer compartment to make it
colder.
If you need to adjust temperatures in the refrigerator or
freezer, start by adjusting the refrigerator and allow 24
hours for the temperature to stabilize. If it is too warm or
too cold, then adjust the freezer control. Use the settings
listed in the chart below as a guide. Always remember to
wait at least 24 hours between adjustments.
CONDITION/REASON: RECOMMENDED
ADJUSTMENT:
REFRIGERATOR section
is too cold
• Controls not set
correctly for your
conditions
Adjust the
REFRIGERATOR setting
to the next lowest number
and wait 24 hours, then
check.
FREEZER section is too
cold
• Controls not set
correctly for your
conditions
Adjust the FREEZER
setting to the next lowest
number and wait 24
hours, then check.
LIGHT/FILTER
ICE TYPE
CRUSH
CUBE
ICE PLUS
HOLD
3 SECS
MONTH
1
2
3
4
5
6
7
8
1
2
3
4
5
6
8
7
ALARM/LOCK
3 SEC