LG 22LG3DCH - Manual (Page 110)

COMMER
CIAL
MODE
SETUP
108
COMMERCIAL MODE SETUP
Editing/Adding Channel ICONs
and/or Labels
If there is no pre-assigned ICON, you can make a custom
channel label of up to 7 characters to help in identifying
the channel or network. At your option, channel labels
can also be added in addition to a pre-assigned
ICON. You may also add labels for the Aux input sources
to clearly identify the devices that are connected to the
Aux inputs.
Editing and adding the labels can only be done if there
are channels entered into the TV’s channel map either by
using the method described in item 6 on previous page,
by cloning or by the use of the master remote control
from the PPV provider.
Note: A blank letter space is available between ‘Z’ and ‘!’.
To Do Channel Editing/Labeling, proceed
as follows
1. Enter TV Installer menu.
2. Once the installer menu appears, press ‘2’, ‘5’, ‘4’,
‘MENU’. This enters the channel label editing mode. Add
your channel icons and channel labels in this menu, see
below. (You can do this more than once.)
3. To exit 2-5-4+Menu when finished press “MENU”.
Adding Channel Icons and Labels in the 2-5-4 + Menu Mode
1 2 3 4 5 6 7
XYZ
XYZ
XYZ
NETWORK
((IIcco on n))
((LLaab beell))
Changing a Channel’s
ICON on Master TV
1. With Channel Up/Down, select the
channel you want to change the
Icon for.
2. With the Right or Left ADJ arrow,
select the letter ‘I’ on the channel
ID display.
3. With the Up or Down arrow, select
the desired ICON you want to
appear to identify the channel. (If
you know the ICON number, enter
the number followed by Enter /
Select.)
4. Proceed with Changing/Adding
Labels or go to the next channel.
Changing/Adding
Channel Labels on
Master TV
1. Channel Up/Down to select the
desired channel.
2. Press the Right or Left ADJ arrow
repeatedly until the numbers 1 to
7 show up. The number shows
the position of the character that
can be changed. Number 1 is the
first character, number 2 the sec-
ond character and so on.
3. With the Up or Down arrow, select
the desired character.
4. Proceed to the next number posi-
tion or use Channel Up/Down to
go to the next channel.
Changing Source Labels
on Master TV
1. Press “INPUT” to select the
desired Aux input source; Video 1,
HDMI etc.
2. Use the Up or Down arrows to
select the desired character for
space 0.
3. Press the Right or Left arrow
repeatedly to select number
spaces 0, 1 etc. The number shows
the position of the character that
can be changed.
4. Press “INPUT” to select the next
Aux source or proceed with
Changing Icon or
Changing/Adding Labels.
• C CH HA AN NN NE ELL U Up p//D Do ow wn n - Tunes in the next channel
in scan.
• LLeefftt//R Riig gh htt A Arrrro ow wss - Select the item to change. If
“I” is shown, the ICON can be changed. If a number
is shown, it indicates the position of the character
that can be changed.
• U Up p//D Do ow wn n A Arrrro ow wss - Select the ICON or the char-
acter to be displayed.
• 0 0 – – 9 9 - Use to enter the index number of the ICON,
if known.
• E EN NT TE ER R//S SE ELLE EC CT T - Changes the ICON after the
number has been entered.
• II N N P P U U T T - Changes to the Aux input labeling menu.
(“Source” on the remote shown in this manual is
INPUT.)
• M M E E N N U U - Exits 2-5-4+Menu mode.
Installer Remote Control Key Functions for Master TV Channel
Editing/Labeling Menu
REFERENCE: PROCEDURES FOR ADDING CHANNEL LABEL
ICONS/CUSTOM CHANNEL LABELS (2-5-4 + MENU MODE)