Document Outline

• Table of Contents
• Introduction
  • How to use this guide
  • Learn More!
  • Safety precautions
• Overview
  • Finding more information
• Setup
  • Installing software
    • Installing HP Designjet 3D Software Solution:
    • Installing firmware to the workstation:
  • Networking the printer
    • Connecting through a network:
    • Connecting directly to a workstation:
  • Establishing network communication with the printer
    • Establishing communication on a dynamic network:
    • Establishing communication on a static network:
  • Installing Firmware on printer
  • Adding the second HP Designjet 3D Material Bay
    • Installing the HP Designjet 3D Material Bay:
• Operation
  • Display panel and keypad
  • System firmware overview
  • HP Designjet 3D Software Solution overview
  • Processing your STL file for printing
    • Opening your STL file with HP Designjet 3D Software Solution:
    • Selecting layer resolution:
    • Selecting model interior fill style:
    • Selecting support style:
    • Selecting the scale of your STL file:
    • Selecting the orientation of your STL file:
    • Adding your STL file to the pack:
    • Printing your STL file:
  • Building a part
    • Starting a build from a remote location:
    • Starting a build from the display panel:
  • The display panel during build
  • Chamber Lights
  • Pausing a build
  • Resuming after pause
  • Canceling a build
  • Removing a completed part
    • Remove a part from the modeling base:
  • Removing HP Designjet 3D Support Material
  • Emptying the purge bucket
  • Replacing material for single material bay
  • Replacing material for dual material bays
  • Material bay LEDs
  • Replacing material spools
    • Removing a spool of material from the carrier:
  • Storing material spools
  • Auto power down
    • Cancelling auto power down:
  • Powering off
  • Resuming operations from Standby mode
  • Updating printer firmware:
    • Installing the firmware:
• Maintenance
  • Daily
    • Empty the purge bucket
    • Inspect the tip wipe assembly
    • Inspect the tip shields
    • Remove debris buildup
    • Vacuum build chamber
    • Clean door
  • Tip wipe assembly
  • Tip shield replacement
  • Remove debris from the Filament Present switch
  • Tip replacement and calibration
    • Removing tips:
    • Installing tips:
    • Tip calibration:
  • Chamber light bar replacement
• Troubleshooting
  • Troubleshooting
  • Fault determination codes
  • Exporting printer configuration (.cfg) file
    • Exporting configuration file from printer:
  • Cycling power
  • Diagnosing loss of extrusion
  • Clogged tip
  • Material Jam
  • Recovering from loss of extrusion
• Support
  • Introduction
  • HP Professional Services
    • Knowledge Center
    • HP Care Packs and Warranty Extensions
    • HP Installation
    • Contact HP Support
    • Telephone number
• Recycling
  • Removing the EEproms from the material guides
  • Removing the desiccant from the material spool
• Printer Specifications
  • Physical specifications
  • Facility specifications
  • Power specifications
  • Ecological specifications
  • Environmental specifications
  • Acoustic specifications
• Supplemental Information
  • HP Designjet 3D and HP Designjet Color 3D Printer series
  • Hewlett Packard Limited Warranty Statement
  • Declaration of conformity
    • declares that the product
    • conforms to the following product specifications
    • Additional information
    • Local contacts for regulatory topics only
  • Regulatory and Environmental Information
    • Regulatory Model Identification Number
    • EMC Class A Warning
    • FCC Statements (U.S.A.)
    • Canada Electromagnetic compatibility (EMC)
    • MSDS (Material Safety Data Sheet)
    • Disposal of waste equipment by users in private households in the European Union
    • Chemical Substances
    • Eco-Tips
    • Environmental product stewardship program
    • Recycling Program